Installation Instructions
Hyundai Accent 4 Dr. & 5 Dr.
Kia Rio 4 Dr. Sedan
Part Numbers:
Hitch Shown In Proper Position
Wiring Access Location: PC3, PC4
Equipment Required:
Wrenches: 11/16”
5 Door Accent
Tie down hook
Do Not Exceed Lower of Towing Vehicle
Manufacturer’s Rating or
Drawbar must be used in the
Rise position only.
Drawbar Kit:
3592
Fastener Kit: 24884F
24884
60301
77272
24899 UH
2000 LB (908 Kg) Max Gross Trailer Weight
200 LB (90.8 Kg) Max Tongue Weight
Kink pullwire to keep
spacer independent of bolt
Reverse pullwire technique
4 Door Accent
Frame rail
2
22
2
3
33
3
4
44
4
5
55
5
6
66
6
7
77
7
7
77
7
7
77
7
8
88
8
3
33
3
4 Door Accent/Rio
Item 7
(1) spacer Accent 5 dr
(2) spacers Accent 4 dr
No spacer Rio 4 dr
5 Door Accent
Tie
down
hook
4 Door Accent/Rio
fascia
5 Door Accent
fascia
8
88
8
Figure 2.
Tie down
bracket
on hitch
Tie down bracket
1
11
1
Hitch bar
Hitch bar
Note: Different configurations due to differences in tie down hooks on each make/model.
Note: Due to different configuration of the vehicles there could be extra spacers, item 7 not used.
1. Remove rubber plug from frame rails if present. Return to owner on the 5 door and replace after hitch installation on 4 dr models.
2. On 4 door models using the pullwire method, item 8 (Figure 2), insert items 1 & 2 through forward hole in frame rail as shown.
On 5 door models use the reverse pullwire method (Figure 3) insert items 1 & 2 through hole. Leave pullwires attached.
3. Insert item 5 carriage bolt through item 6 spacer and then through the tie down hook.
4. Feed the pullwires through the slot on the hitch bars.
5. Place item 7 as needed, (1 spacer, 2 spacers, or no spacers), in position on the hitch tie down bracket as shown.
6. Raise the hitch into position being careful not to push the fasteners into the frame rails. Remove pullwire and attach items 3 & 4
as shown.
7. Use remaining fasteners to attach to the tie down hook as shown in Figure 1.
8. Tighten all fasteners to the required torque specification.
© 2012 Cequent Performance Products, Inc.
Sheet 1 of 3 24884N 4-13-12 Rev. A
1
11
1
Qty. (2) Carriage bolt 7/16-14 X 2.00 GR5
5
55
5
Qty. (1) Carriage bolt 7/16-14 X 2.50 GR5
2
22
2
Qty. (2) Spacer .13 X .93 X 3.00, Round corners
6
66
6
Qty. (1) Spacer .25 X 1.00 X 3.00, Square corners
3
33
3
Qty. (3) Conical washer 7/16
7
77
7
Qty. (2) Spacer .25 X 1.50 X 3.00
4
44
4
Qty. (3) Hex nut 7/16-14
8
88
8
Qty. (2) Pullwire 7/16
Note: check hitch frequently, making sure all fasteners and ball are properly tightened. If hitch is removed, plug all holes in trunk pan or other body panels to
prevent entry of water and exhaust fumes. A hitch or ball which has been damaged should be removed and replaced. Observe safety precautions when working
beneath a vehicle and wear eye protection. Do not cut access or attachment holes with a torch.
This product complies with safety specifications and requirements for connecting devices and towing systems of the state of New York, V.E.S.C. Regulation V-5
and SAE J684.
Tighten all 7/16-14 GR5 fasteners with torque wrench to 50 Lb.-Ft. (68 N*M)
Example of
pullwire procedure
4
44
4
Note: sort hardware prior to hitch installation to confirm longer 7/16 bolt length for tie down
hook, and small spacers round corners vs. square corners installation
Figure 1.
(3 Seiten)
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Kommentare zu diesen Handbüchern