Draw-tite 24832 SPORTFRAME HITCH Bedienungsanleitung PDF herunterladen

Drill Bits: 1-1/8 hole saw

24832

Installation Instructions

Mazda 6

Part Numbers:

60222

77205

Hitch Shown In Proper Position

Wiring Access Location: PC3, PC4

Equipment Required: Hole Saw, fish wire (provided)

Wrenches: 11/16”

1. Raise car on ramps or hoist.

2. Lower exhaust pipe by removing the rubber isolator(s) at the muffler(s) and one isolator near the rear suspension. Support the

exhaust to prevent damage.

NOTE; 6 cylinder models with exhaust trim in rear fascia – remove two black plastic fascia fasteners near the center of the rear panel.

This will allow the fascia to be pulled gently back and down enough to remove tail pipe from exhaust trim.

3. Raise hitch into place and temporarily install the fasteners in the rear panel. This will locate the hitch.

4. Using the hitch as a template, mark the forward most hole. Lower the hitch and drill a 1-1/8” access hole in the frame as shown.

5. Paint any bare metal and fish wire the frame rail fasteners into place through the access hole. Leave the fish wires attached.

6. Raising hitch into position, routing fish wires thru hitch holes, being careful not to push fasteners back into the frame.

7. Remove the fish wires, install the remaining fasteners as shown above and tighten to spec.

8. Raise the exhaust back into position an reconnect to rubber isolators. Reinstall black fascia fasteners if removed.

Rev. A10-29-0824832NSheet 1 of 3

z 2008 Cequent Towing Products

Washer – flat 7/16”Qty. (2)

Washer – conical 7/16”Qty. (6)

Hex head bolt – 7/16 -14 x 1-1/2” long grade 5Qty. (2)

Block – 1x2x3/16”Qty. (4)

Nut – 7/16 -14Qty. (6)

Carriage bolt – 7/16-14 x 1-1/4” long grade 5Qty. (4)

Tighten all 7/16” fasteners with torque wrench to 50 Lb.-Ft.(68 n*m)

Note: check hitch frequently, making sure all fasteners and ball are properly tightened. If hitch is removed, plug all holes in trunk pan or other body panels to

prevent entry of water and exhaust fumes. A hitch or ball which has been damaged should be removed and replaced. Observe safety precautions when working

beneath a vehicle and wear eye protection. Do not cut access or attachment holes with a torch.

This product complies with safety specifications and requirements for connecting devices and towing systems of the state of New York, V.E.S.C. Regulation V-5

and SAE J684.

2000 LB (908 Kg) Max Gross Trailer Weight

200 LB (90.8 Kg) Max Tongue Weight

Do Not Exceed Lower of Towing Vehicle

Manufacturer’s Rating or

Drawbar must be used in the

RISE

position only.

Drawbar Kit:

3592

Fastener Kit: 24832F

Fastener are typical

For both sides

Drilled access hole

Existing holes

Rear Panel

Fascia

Form F206 Rev A 5605

1 2 3

Inhaltsverzeichnis

Seite 1 - Installation Instructions

Drill Bits: 1-1/8 hole saw24832Installation InstructionsMazda 6Part Numbers:6022277205Hitch Shown In Proper PositionWiring Access Location: PC3, PC4Eq

Seite 2 - Instructions d’installation

Mèche : Scie-cloche 1-1/824832Instructions d’installationMazda 6Numéros de pièces :6022277205Attelage montré dans la position appropriéePoints d’accès

Seite 3 - Instrucciones de instalación

Brocas de taladro: Sierra de copa 1-1/824832Instrucciones de instalación Mazda 6Números de partes:6022277205El enganche se muestra en la posición cor