Draw-tite 24860 SPORTFRAME HITCH Bedienungsanleitung PDF herunterladen

Installation Instructions

Lexus HS 250h

Part Numbers:

24860

60276

77237

Hitch Shown In Proper Position

Wiring Access Location:

Equipment Required: 8” Ratchet Extension

Wrenches: 10mm, 17mm, 19mm

Frame

rail

1. Remove the tie-down hook on driver’s side. Note: remove the bolts leaving the appearance panel in

place. Return tie-down hook and fasteners to vehicle owner.

2. Lower exhaust at (2) hangers, (1) at front and (1) at rear of muffler. Note: Spraying a lubricant or soapy

water on the metal hanger rod and the rubber isolator helps removal. Be careful not to allow muffler to

fall under its own weight.

3. Temporarily remove exhaust heat shield. Use a marker or tape to mark heat shield for trimming and

confirm the trim. Trim heat shield and reattach.

4. Raise the driver’s side of the hitch into position through the tie-down bracket opening. With the

passengers side on the ground rotate the hitch through the cut-out. Leave hitch supported (jack, blocks,

person).

5. Raise the passengers side of the hitch over the tail pipe, sandwiching heat shield between the frame and

bracket. Gently bend heat shield back into position. Loosely install fasteners.

6. Install remaining fasteners as shown.

7. Tighten all fasteners to the required torque specification.

8. Reinstall exhaust.

Tighten all M12 CL8.8 fasteners with torque wrench to 65 Lb.-Ft. (88 N*M)

z 2010, 2012 Cequent Performance Products

Sheet 1 of 3 24860N 1-9-12 Rev. B

Qty. (4) Hex bolt M12 X 1.25 X 35 CL8.8

Qty. (4) Conical washer 1/2”

Note: check hitch frequently, making sure all fasteners and ball are properly tightened. If hitch is removed, plug all holes in trunk pan or other body panels to

prevent entry of water and exhaust fumes. A hitch or ball which has been damaged should be removed and replaced. Observe safety precautions when working

beneath a vehicle and wear eye protection. Do not cut access or attachment holes with a torch.

This product complies with safety specifications and requirements for connecting devices and towing systems of the state of New York, V.E.S.C. Regulation V-5

and SAE J684.

Do Not Exceed Lower of Towing Vehicle

Manufacturer’s Rating or

Drawbar must be used in the

Rise position only.

Drawbar Kit:

3594

Fastener Kit: 24860F

Form F206 Rev A 5605

2000 LB (908 Kg) Max Gross Trailer Weight

200 LB (90.8 Kg) Max Tongue Weight

Appearance

panel

Fascia

Frame

rail

Tie down bracket opening

on appearance panel

Note: Fasteners typical both sides

Appearance panel shown

off vehicle

Tie down

bracket opening

Appearance panel not shown

installation view for clarity

4” / 102 mm

3” / 77 mm

1/2” / 13 mm

Heat Shield

Heat shield not

shown installation

view for clarity

Tie down hook

1 2 3

Inhaltsverzeichnis

Seite 1 - Installation Instructions

Installation Instructions Lexus HS 250h Part Numbers: 24860 60276 77237 Hitch Shown In Proper Position Wiring Access Location: Equ

Seite 2 - Instructions d’installation

Instructions d’installation Numéros de pièces : Attelage montré dans la position appropriée Points d’accès au câblage : Équipement requis : Rallonge

Seite 3 - 60276

Instrucciones de instalación Números de partes: El enganche se muestra en la posición correcta Ubicación del acceso al cableado: Equipo necesario:

Kommentare zu diesen Handbüchern

Keine Kommentare

Draw-tite 24860 SPORTFRAME HITCH Bedienungsanleitung

Stöbern Sie online oder laden Sie Bedienungsanleitung nach Für das Auto Draw-tite 24860 SPORTFRAME HITCH herunter. Draw-Tite 24860 SPORTFRAME HITCH User Manual Benutzerhandbuch

Inhaltsverzeichnis

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Für das Auto Draw-tite 24860 SPORTFRAME HITCH