Draw-tite 24914 SPORTFRAME HITCH Bedienungsanleitung PDF herunterladen

Installation Instructions

Mazda 3 5 Door

Part Numbers:

24914

60346

77301

Hitch Shown In Proper Position

Wiring Access Location: PC3, 4

Equipment Required: Pullwire (provided), lubricant or

soapy water, flashlight, & utility knife.

Wrenches: 11/16”, & 19mm

Drill Bits: None

Access hole

1. Locate rear weldnut on the outside of the frame rails above the access hole. Using the utility knife remove tape covering weldnut

and check threads by running the M12 hex bolt into, then removing hex bolt.

2. Feed spacers and carriage bolts into position using the pull wires provided into each frame rail (middle slot as shown). Leave pull

wire attached. Note: It is much easier if bolt and spacer are not engaged while inserting them into frame, refer to illustration.

3. Lower exhaust system at the rubber isolator (4). Spraying a lubricant or soapy water on the metal hanger rod and the rubber

isolator helps with removal. Do not let the exhaust drop, support the exhaust during installation.

4. Raise hitch into position (feed pull wires through the slots on the bars), sliding the hitch through the exhaust cutouts on the fascia

and into position. Remove the pull wires and attach the 7/16” conical and hex nut loosely to hitch for support.

5. Install the ½” conical and M12 bolt into the existing weldnut.

6. Raise exhaust back into position using an lubricant or soapy water.

7. Torque all fasteners to specifications shown below.

z 2013 Cequent Performance Products, Inc

Sheet 1 of 3 24914N 12-6-13 Rev. A

Qty. (2) Hex bolt M12 X 1.25 X 30 CL8.8

Qty. (2) Spacer .250 X .875 X 3.00

Qty. (2) Conical washer ½”

Qty. (2) Conical washer 7/16”

Qty. (2) Carriage bolt 7/16-14 X 14 X 1.75 GR5

Qty. (2) Hex nut 7/16-14

Tighten all M12 CL8.8 fasteners with torque wrench to 68 Lb.-Ft. ( 92 N*M)

Tighten all 7/16-14 GR5 fasteners with torque wrench to 50 Lb.-Ft. (68 N*M)

Note: check hitch frequently, making sure all fasteners and ball are properly tightened. If hitch is removed, plug all holes in trunk pan or other body panels to prevent

entry of water and exhaust fumes. A hitch or ball which has been damaged should be removed and replaced. Observe safety precautions when working beneath a

vehicle and wear eye protection. Do not cut access or attachment holes with a torch.

This product complies with safety specifications and requirements for connecting devices and towing systems of the state of New York, V.E.S.C. Regulation V-5 and

SAE J684.

Do Not Exceed Lower of Towing Vehicle

Manufacturer’s Rating or

Drawbar must be used in the

RISE position only.

Drawbar Kit:

3593

Fastener Kit: 24914F

Form F206 Rev B 9

2012

Accessory Rating

Printed in Mexico

2000 LB (908 Kg) Max Gross Trailer Weight

200 LB (90.8 Kg) Max Tongue Weight

Note: Fasteners typical both sides

Note: sort hardware prior to hitch installation to confirm

conical washer are kept with coordinated with bolts.

Kink pull wire to keep

spacer independent of bolt

Vehicle forward

Carriage bolt slot

Access hole

Frame rail

Fascia

1 2 3

Inhaltsverzeichnis

Seite 1 - Installation Instructions

Installation InstructionsMazda 3 5 DoorPart Numbers:24914 60346 77301Hitch Shown In Proper PositionWiring Access Location: PC3, 4Equipment Required:

Seite 2 - Instructions d’installation

Instructions d’installationMazda 3 – 5 portesNuméros de pièce :24914 60346 77301Attelage montré dans la position appropriéePoints d'accès au câbl

Seite 3 - Instrucciones de instalación

Instrucciones de instalaciónMazda 3 de 5 puertasNúmeros de partes:24914 60346 77301El enganche se muestra en la posición correctaUbicación del acceso

Kommentare zu diesen Handbüchern

Keine Kommentare

Draw-tite 24914 SPORTFRAME HITCH Bedienungsanleitung

Stöbern Sie online oder laden Sie Bedienungsanleitung nach Für das Auto Draw-tite 24914 SPORTFRAME HITCH herunter. Draw-Tite 24914 SPORTFRAME HITCH User Manual [es] Benutzerhandbuch

Inhaltsverzeichnis

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Für das Auto Draw-tite 24914 SPORTFRAME HITCH