Draw-tite 24763 SPORTFRAME HITCH Bedienungsanleitung

Stöbern Sie online oder laden Sie Bedienungsanleitung nach Für das Auto Draw-tite 24763 SPORTFRAME HITCH herunter. Draw-Tite 24763 SPORTFRAME HITCH User Manual Benutzerhandbuch

  • Herunterladen
  • Zu meinen Handbüchern hinzufügen
  • Drucken
  • Seite
    / 3
  • Inhaltsverzeichnis
  • LESEZEICHEN
  • Bewertet. / 5. Basierend auf Kundenbewertungen
Seitenansicht 0
Installation Instructions
Honda Civic
Including SI & Hybrid
Part Numbers:
77139
24763
60822
Hitch Shown In Proper Position
Wiring Access Location: PC3, PC4
Equipment Required:
Wrenches: 3/4, 9/16, 10mm,
Drill Bits: ½ drill on some
models required.
2000 LB (908 Kg) Max Gross Trailer Weight
200 LB (90.8 Kg) Max Tongue Weight
Do Not Exceed Lower of Towing Vehicle
Manufacturer’s Rating or
Drawbar must be used in the
Rise position only.
Fastener Kit: 24763F
Drawbar Kit:
3593
Exhaust
Heat Shield
Frame Rail
Tow Hook
Fascia
1
2
3
3
2
1
On Hybrid: Trim heat
shield as required to allow
handle nut to be installed.
Sandwich heat shield
between frame and hitch.
On Hybrid: Remove or trim
1. Lower vehicle exhaust by removing tailpipe tangs out of rubber exhaust hanger at rear of vehicle.
2. On the Passenger’s side remove the (4) bolts that attach the exhaust heat shield to the vehicle. (Do not Discard).
3. On the Driver’s side, remove the plastic rivet and nut that hold the plastic shroud to the frame rail. (Do not Discard).
4. Raise hitch into position with frame bracket flanges between the frame rail and plastic shroud on the Driver’s side and between
the frame rail and exhaust heat shield on the Passenger’s side. Make sure that tailpipe tangs are above hitch bar while
raising hitch in to place. On some vehicles it may be necessary to remove chrome decorative ring off of end of tailpipe to
allow muffler to slide sideways toward middle of vehicle to allow better wrench access.
5. Insert 1/2”-13 handle nuts through the large holes in vehicle frame rails and install fasteners as shown above.
6. Insert the 3/8-16 U-bolt through the vehicle tow hook and insert through the mounting holes located on the hitch, (see above).
7. Tighten all fasteners to the required torque specifications shown below.
8. Reinstall exhaust heat shield over hitch Reattach exhaust to hanger & replace rivet and nut holding plastic shroud on
Driver’s side. Heat shield may require trimming. Reattach chrome decorative ring to tailpipe if removed.
Tighten all 1/2 fasteners with torque wrench to 50 Lb.-Ft. (68 N*M)
z 2006, 2007, 2012 Cequent Performance Products, Inc
Sheet 1 of 3 24763N 1-20-12 Rev. F
Qty. (2) ½-13 Hex Bolt GR5 Qty. (1) 3/8-16 U-Bolt GR2
Qty. (2) ½ Conical Toothed Washer Qty. (2) 3/8-16 Flanged Lock Nut
Qty. (2) ½-13 Handle Nut
Tighten all 3/8 fasteners with torque wrench to 20 Lb.-Ft. (27 N*M)
Note: check hitch frequently, making sure all fasteners and ball are properly tightened. If hitch is removed, plug all holes in trunk pan or other body panels to
prevent entry of water and exhaust fumes. A hitch or ball which has been damaged should be removed and replaced. Observe safety precautions when working
beneath a vehicle and wear eye protection. Do not cut access or attachment holes with a torch.
This product complies with safety specifications and requirements for connecting devices and towing systems of the state of New York, V.E.S.C. Regulation V-5
and SAE J684.
1
2
4
3
2
1
5
Drill to enlarge holes on
inner layer of frame rails
if necessary.
On Hybrid: Remove or trim
plastic appearance panel.
Seitenansicht 0
1 2 3

Inhaltsverzeichnis

Seite 1 - Installation Instructions

Installation InstructionsHonda CivicIncluding SI & HybridPart Numbers:771392476360822Hitch Shown In Proper PositionWiring Access Location: PC3, PC

Seite 2 - Instructions d’installation

Instructions d’installationHonda CivicY compris SI et HybridNuméros de pièces :771392476360822Attelage montré dans la position appropriéePoints d’accè

Seite 3 - Instrucciones de instalación

Instrucciones de instalación Honda CivicIncluye SI e HíbridoNúmeros de partes:771392476360822El enganche se muestra en la posición correcta Ubicación

Kommentare zu diesen Handbüchern

Keine Kommentare