Draw-tite 24787 SPORTFRAME HITCH Bedienungsanleitung PDF herunterladen

Installation Instructions

HONDA ACCORD

Includes Hybrid

6 cylinder

Part Numbers:

60953

24787

77161

Wiring Access Location: PC3

Equipment Required:

Wrenches: 11/16”, 3/4”

Drill Bits: 9/16”

1. Lower exhaust by removing both rubber isolators from muffler hangers. Be careful not to allow mufflers to fall under their own weight.

2. Both heat shields will need to be marked and drilled 4 1/2” from the forward most hole on the frame channel. Mark holes then hold

hitch in position to check. Refer to illustration for clarification. Remove heat shield to drill.

3. Thread bolt leader (9) onto end of carriage bolt (1) and insert bolt leader through reinforcing plate (7). Fish the bolt leader and

assembly through the access hole in frame and carefully pull through existing hole in frame till bolt is in position. Leave bolt leaders

attached so the hardware does not get pushed back inside the frame. Repeat for other side of vehicle.

4. Reinstall heat shields once the carriage bolts (1) are in position.

5. Install 1-1/2” carriage bolt (4) through square hole in hitch and vehicle’s tie down loop from driver’s side. Install clamping block (8) and

conical toothed washer (5) and nut (6) and hand tighten to hold hitch in place.

6. Fish bolt leaders through holes in hitch’s frame straps and being careful not to push bolt assemblies back into frame channels, raise

hitch’s frame straps up to vehicle’s frame, remove bolt leaders and install conical toothed washers (2) and nuts (3).

7. Tighten all bolts, referring to torque table on instruction sheet.

8. Raise exhaust back into position and reinstall rubber isolators.

Tighten all 1/2” fasteners with torque wrench to 75 Lb.-Ft. (102N*M)

Rev. C9-29-0824787NSheet 1 of 6

z 2005, 2007, 2008 Cequent Towing Products

BLOCK; CLAMPING, 1-1/2” X 3”Qty. (1)

BOLT CARRIAGE 1/2”-13 X 1 1/2” GR 5Qty. (1)

PLATE REINFORCEMENTQty. (2)

NUT – 7/16”Qty. (2)

NUT – 1/2”Qty. (1)

WASHER CONICAL TOOTH 7/16”Qty. (2)

WASHER CONICAL TOOTH 1/2”Qty. (1)

BOLT CARRIAGE 7/16” - 14 X 1 1/2” GR 5Qty. (2)

Tighten all 7/16 fasteners with torque wrench to 50 Lb.-Ft. (68 N*M)

Note: check hitch frequently, making sure all fasteners and ball are properly tightened. If hitch is removed, plug all holes in trunk pan or other body panels to

prevent entry of water and exhaust fumes. A hitch or ball which has been damaged should be removed and replaced. Observe safety precautions when working

beneath a vehicle and wear eye protection. Do not cut access or attachment holes with a torch.

This product complies with safety specifications and requirements for connecting devices and towing systems of the state of New York, V.E.S.C. Regulation V-5

and SAE J684.

2000 LB (908Kg) Max Gross Trailer Weight

200 LB (91Kg) Max Tongue Weight

Do Not Exceed Lower of Towing Vehicle

Manufacturer’s Rating or

Drawbar must be used in the

RISE

position only.

Drawbar Kit:

3592

Fastener Kit: KA-8002-249

Form F206 Rev A 5605

FRAME RAIL

TIE DOWN LOOP

4 1/2” (114.3 mm)

For vehicles with appearance

panel:

Remove appearance panel which

covers the trunk pan.

(2)10mm

Remove the (2) plastic rivets that

fasten the fascia tabs to the

vehicle. Note: Remove the center

of the rivet with a screwdriver.

Rivets to be reinstalled.

Return appearance panel and

fasteners to vehicle owner.

BOLT LEADER

Qty. (2)

1 2 3 4 5 6

Inhaltsverzeichnis

Seite 1 - Installation Instructions

Installation InstructionsHONDA ACCORDIncludes Hybrid6 cylinder Part Numbers:609532478777161Wiring Access Location: PC3Equipment Required:Wrenches: 11/

Seite 2

Installation InstructionsHONDA ACCORD4 cylinder Part Numbers:609532478777161Wiring Access Location: PC3Equipment Required:Wrenches: 11/16”, 3/4”Drill

Seite 3 - Instructions d’installation

Remarque : Vérifier l’attelage fréquemment, en s’assurant que toute la visserie et la bille sont serrées adéquatement. Si l’attelage est enlevé, bouc

Seite 4

Instructions d’installationHONDA ACCORD4 cylindresNuméros de pièces :609532478777161Point d’accès au câblage : PC3Équipement requis :Clés : 11/16”, 3/

Seite 5 - Instrucciones de instalación

Instrucciones de instalaciónHONDA ACCORD Incluye los Híbridos6 cilindros Números de partes:609532478777161Ubicación del acceso

Seite 6

Instrucciones de instalaciónHONDA ACCORD4 cilindros Números de partes:609532478777161Ubicación del acceso al cableado: PC3Equipo necesario:Llaves: 11/

Kommentare zu diesen Handbüchern

Keine Kommentare

Draw-tite 24787 SPORTFRAME HITCH Bedienungsanleitung

Stöbern Sie online oder laden Sie Bedienungsanleitung nach Für das Auto Draw-tite 24787 SPORTFRAME HITCH herunter. Draw-Tite 24787 SPORTFRAME HITCH User Manual Benutzerhandbuch

Inhaltsverzeichnis

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Für das Auto Draw-tite 24787 SPORTFRAME HITCH