Draw-tite 65049 FRONT MOUNT RECEIVER Bedienungsanleitung PDF herunterladen

Front Mounted Receiver

Installation Instructions

Ford SuperDuty 250/350/450

All including Cab-on-Chassis

Part Numbers:

65049

Bumper

Ai d

Truck cab mount

Truck frame

Equipment Required:

Wrenches: 13/16”, 7/8”,

15/16” ,18mm

Drill Bits: None

Fastener Kit: 65049F

CARGO CAPACITY

–

Do not exceed

500 LB. or Truck Front

Gross Axle Weight Rating, (GAWR).

9,000lb.

MAXIMUM WINCH LINE PULL

Receiver Shown In Proper Position

Forward truck

frame

Truck frame cut-away to

show Bolt Leader through

slot in truck frame

slot

truck

frame

Forward truck cab

mount bracket

Mount bracket cut-away

to show detail

1234

Rear tab of hitch aligns with slot

in frame between mount bracket

This is a magnified

view of a Bolt Leade

Bolt Leader sho n

1234

567 8

End of Bolt Leader

Remove existing brackets if present

both sides. Return to owner.

On newer models with bracket on outside of

frame insert this bolt from opposite direction

On some models be careful

ihl ilii

Qty. (2) Hex Bolt, 9/16”-12 x 2” Gr5 Qty. (2) Carriage Bolt, 5/8”-11 X 2” Gr5

Qty. (2) Flat Washer, 9/16” Qty. (2) Lock Washer, 5/8”

Qty. (2) Lock Washer, 9/16” Qty. (2) Hex Nut, 5/8”

Qty. (2) Hex Nut, 9/16” Qty. (1) Bolt Leader, 5/8”

Bolt

Leader

sho

567 8

not to p

ectr

between hitch and bumper.

1. On newer model trucks it is necessary to trim or cut opening in plastic air dam attached to bottom of bumper.

2. It may also be necessary to remove existing frame end brackets if present. See above.

3. Position hitch and install fasteners as shown above. Using 5/8” bolt leader to pull 5/8” carriage bolt into frame slot.

4. Torque fasteners to specifications below.

Tighten all 9/16” GR5 fasteners with torque wrench to 110 Lb.-Ft (149 N-M).

CONSULT VEHICLE OWNER BEFORE TRIMMING OR CUTTING PLASTIC AIR DAM.

Tighten all 5/8” GR5 fasteners with torque wrench to 150 Lb.-Ft (203 N-M).

z 2007, 2009 Cequent Performance Products

Sheet 1 of 3 65049N 10-12-09 Rev. C

Note: check hitch frequently, making sure all fasteners and ball are properly tightened. If hitch is removed, plug all holes in trunk pan or other body

panels to prevent entry of water and exhaust fumes. A hitch or ball which has been damaged should be removed and replaced. Observe safety

precautions when working beneath a vehicle and wear eye protection. Do not cut access or attachment holes with a torch.

This product complies with safety specifications and requirements for connecting devices and towing systems of the state of New York, V.E.S.C.

Regulation V-5 and SAE J684.

1 2 3

Inhaltsverzeichnis

Seite 1 - Installation Instructions

Front Mounted ReceiverInstallation InstructionsFord SuperDuty 250/350/450 All including Cab-on-ChassisPart Numbers:65049BumperAi dTruck

Seite 2 - Instrucciones de instalación

Receptor instalado por el frenteInstrucciones de instalaciónFord SuperDuty 250/350/450 Todos los modelos incluido Cab-on-ChassisNúmer

Seite 3 - Instructions d’installation

Récepteur à montage avantInstructions d’installationFord SuperDuty 250/350/450 Tous comprennent les modèles Cab-on-ChassisNuméro de piè

Kommentare zu diesen Handbüchern

Keine Kommentare

Draw-tite 65049 FRONT MOUNT RECEIVER Bedienungsanleitung

Stöbern Sie online oder laden Sie Bedienungsanleitung nach Für das Auto Draw-tite 65049 FRONT MOUNT RECEIVER herunter. Draw-Tite 65049 FRONT MOUNT RECEIVER User Manual [ru] Benutzerhandbuch

Inhaltsverzeichnis

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Für das Auto Draw-tite 65049 FRONT MOUNT RECEIVER