Draw-tite 41935 ULTRA FRAME RECEIVER Bedienungsanleitung PDF herunterladen

Installation Instructions

Toyota Tundra

Part Numbers:

41935

Hitch Shown In Proper Position

Equipment Required:

Wrenches: 17mm, 19mm, 21mm

Drill Bits: None

1. Remove existing angle brackets, both sides, between truck frame rails and truck bumper brackets. Return to owner.

Save bolts as they will be reinstalled in Steps 2 & 3.

2. Raise hitch into position as shown and reinstall M14 bolts removed in Step 1through hitch and bumper bracket. Bolts must face

outwards as shown. Place 9/16” flat washers, lockwashers and M14 flanged hex nuts on these bolts on outside of truck bumper

bracket. Hand tight only.

3. Place a toothed conical washer over each M12 bolt removed in Step 1, and then reinstall M12 bolts through hitch and into

weldnuts in truck frame. Hand tight only.

4. Install M14-1.50 bolts supplied through 9/16” helical lockwashers and blocks. Install these through hitch and then through blocks

into frame weldnuts, typical (4) places. Hand tight only.

5. If existing electrical bracket on bottom of truck bumper contacts top of hitch tube, then bend up out of the way. It may be

necessary to cut bolts holding electrical bracket shorter so that bracket can be pushed up farther.

6. Torque M12 bolts to specifications below first. Then torque M14 bolts in bumper brackets to specifications below next.

Torque M14 bolts forward on frame to specifications below last.

Rev. A03-20-0741935NSheet 1 of 3

z 2007 Cequent Towing Products

1/4” X 1-1/2” X 2” BlockQty. (8)9/16” Helical lock washerQty. (8)

M14-1.50 X 45mm Cl. 10.9 Hex boltQty. (4)M14-1.50 Flanged hex nutQty. (4)

9/16” Flat washerQty. (4)1/2” Conical washer, toothed.Qty. (4)

Torque all M12 fasteners with torque wrench to 130 lb.-Ft.(176 N*M) Torque all M14 fasteners with torque wrench to 148 lb.-Ft. (201 N*M)

Note: check hitch frequently, making sure all fasteners and ball are properly tightened. If hitch is removed, plug all holes in trunk pan or other body panels to

prevent entry of water and exhaust fumes. A hitch or ball which has been damaged should be removed and replaced. Observe safety precautions when working

beneath a vehicle and wear eye protection. Do not cut access or attachment holes with a torch.

This product complies with safety specifications and requirements for connecting devices and towing systems of the state of New York, V.E.S.C. Regulation V-5

and SAE J684.

Fastener Kit: 41935F

Do Not Exceed Lower of Towing Vehicle

Manufacturer’s Rating or

1200 (545)12,000 (5448)

Weight Carrying

Ball Mount

1400 (636)14,000 (6356)

Weight Distributing

Max Tongue

WT- lb (Kg)

Max Gross

Trailer WT- lb (Kg)

Hitch type

Wiring Access Location: PU3

Form: F205 Rev A 5-6-05

Bumper

Bumper bracket

Frame

Remove existing

brackets both sides.

Return to owner.

Place blocks between

outside of frame and hitch.

ALL FASTENERS

TYPICAL BOTH SIDES.

Existing M12-1.25

bolts, (4) total.

Existing M14-1.50

bolts, (4) total.

Existing weldnuts

in frame

1 2 3

Inhaltsverzeichnis

Seite 1 - Installation Instructions

Installation InstructionsToyota TundraPart Numbers:41935Hitch Shown In Proper PositionEquipment Required:Wrenches: 17mm, 19mm, 21mmDrill Bits: None1.

Seite 2 - Instructions d’installation

Instructions d’installationToyota TundraNuméro de pièce :41935Attelage montré dans la position appropriéeÉquipement requis :Clés : 17 mm, 19 mm, 21 mm

Seite 3 - Instrucciones de instalación

Instrucciones de instalaciónToyota TundraNúmeros de partes:41935El enganche se muestra en la posición correcta Equipo necesario:Llaves: 17mm, 19mm, 2

Kommentare zu diesen Handbüchern

Keine Kommentare

Draw-tite 41935 ULTRA FRAME RECEIVER Bedienungsanleitung

Stöbern Sie online oder laden Sie Bedienungsanleitung nach Für das Auto Draw-tite 41935 ULTRA FRAME RECEIVER herunter. Draw-Tite 41935 ULTRA FRAME RECEIVER User Manual Benutzerhandbuch

Inhaltsverzeichnis

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Für das Auto Draw-tite 41935 ULTRA FRAME RECEIVER