Draw-tite 40050 CLASS III-IV MULTI-FIT RECEIVER Bedienungsanleitung PDF herunterladen

CATALOG NO.

40050, 82000

INSTALLATION INSTRUCTIONS

NOTE: CHECK HITCH FREQUENTLY, MAKING SURE ALL FASTENERS AND BALL ARE PROPERLY TIGHTENED. A HITCH OR BALL WHICH HAS BEEN

DAMAGED SHOULD BE REMOVED AND REPLACED. OBSERVE SAFETY PRECAUTIONS WHEN WORKING BENEATH A VEHICLE AND WEAR EYE

PROTECTION. FOLLOW CAR MAKER'S SPECIFICATIONS FOR MAXIMUM TRAILER WEIGHT AND TONGUE WEIGHT. DO NOT CUT ACCESS OR

ATTACHMENT HOLES WITH A TORCH.

- MAXIMUM RATINGS –

DO NOT EXCEED LOWER OF TOWING VEHICLE MANUFACTURER'S RATINGS OR THOSE LISTED BELOW:

WEIGHT DISTRIBUTING WEIGHT CARRYING

10,000 LBS. GROSS TRAILER WEIGHT 6,000 LBS. GROSS TRAILER WEIGHT

1,000 LBS. TONGUE WEIGHT 600 LBS. TONGUE WEIGHT

TOOLS REQUIRED:

Drill bits - 3/16" (.1875), 9/32 (.281), 1/2" (.500), and 17/32" (.531)

Sockets and wrenches - 3/4, 13/16, and 7/8, 13mm, 18mm, 19mm

Wire - #19 soft galvanized or equivalent

Wire - 1/32" diameter or equivalent

Center Punch

Clamps

Files - round & flat

1. REMOVE PICKUP TRUCK SPARE TIRE AT END OF FRAME FROM ITS UNDER BED MOUNTING. THIS IS NOT REQUIRED FOR EACH

INSTALLATION BUT WILL MAKE RECEIVER INSTALLATION EASIER. IT IS TO BE REINSTALLED WHEN INSTALLATION IS COMPLETE.

2. MEASURE THE OUTSIDE WIDTH OF THE FRAME. IT SHOULD MEASURE APPROXIMATELY 34" OR 37-1/2" OR 38".

3. ASSEMBLE THE RIGHT AND LEFT SIDE BRACKETS TO THE CROSSTUBE ASSEMBLY AS SHOWN ABOVE. THE INSIDE HOLES IN THE SIDE

BRACKETS ARE USED FOR 37-1/2" AND 38" WIDE FRAMES AND THE OUTSIDE HOLES ARE USED FOR 34" WIDE FRAMES. SLOTS IN THE

CROSSTUBE MUST LINE UP WITH THE HOLES IN THE SIDE BRACKETS. CAUTION: DO NOT DRILL NEW HOLES IN ANY RECEIVER PART.

4. INSTALL THE 9/16-18 X 1-1/2 GR5 HEX BOLTS, HARDENED FLAT WASHERS, AND FLANGE LOCKNUTS AS SHOWN ABOVE. DO NOT TIGHTEN

AT THIS TIME. DO NOT USE ONE LONG THROUGH-BOLT OR SUBSTITUTE REGULAR NUTS FOR THE LOCKNUTS INSIDE THE CROSSTUBE

ASSEMBLY.

5. READ THE GENERAL NOTES ON PAGE 6 AND THEN CONTINUE INSTALLATION BY FOLLOWING THE INSTRUCTIONS FOR YOUR

PARTICULAR VEHICLE APPLICATION WHICH IS LISTED ON THE FOLLOWING PAGES.

THIS PRODUCT COMPLIES WITH SAFETY SPECIFICATIONS AND REQUIREMENTS FOR CONNECTING DEVICES AND TOWING SYSTEMS OF THE

STATE OF NEW YORK AND V.E.S.C. REGULATION V-5.

-1-

06/09/08 .

1 2 3 4 5 6

Inhaltsverzeichnis

Seite 1 - INSTALLATION INSTRUCTIONS

CATALOG NO. 40050, 82000 INSTALLATION INSTRUCTIONS NOTE: CHECK HITCH FREQUENTLY, MAKING SURE ALL FASTENERS AND BALL ARE PROPERLY TIGHTENED. A

Seite 2

CHEVROLET & GMC PICKUP TRUCKS WITH 34" FRAMES DOES NOT FIT UNITS WITH 6' BED OR 4WD WITH HEAVY DUTY SUSPENSION 1. TIGHTEN THE 9

Seite 3

DODGE PICKUP TRUCK - FULL SIZE - 1967-1993 SPARE TIRE CARRIER WILL HAVE TO BE MODIFIED TO RETAIN UNDER VEHICLE STOWAGE. SPARE TIRE CAN ALSO BE RE

Seite 4

DODGE RAM PICKUP TRUCK - FULL SIZE - 1994-PRESENT FORWARD HOLES TO BE DRILLED ON 6 FT. BED NO DRILLING REQUIRED - (8 Ft. BED ONLY) - USES ALL

Seite 5 - FORD CAB & CHASSIS

FORD F-SERIES - FULL SIZE PICKUP TRUCKS 1979 AND EARLIER 34" & 38" WIDE FRAMES INCLUDES 1999 AND LATER F350 SUPER DUTY CAB & CHAS

Seite 6 - GENERAL NOTES

FORD BRONCO - FULL SIZE 1. RAISE RECEIVER INTO POSITION, CENTERING THE LARGE 1" X 2" SLOT IN THE SIDE BRACKET ASSEMBLY OVER THE RIV

Kommentare zu diesen Handbüchern

Keine Kommentare

Draw-tite 40050 CLASS III-IV MULTI-FIT RECEIVER Bedienungsanleitung

Stöbern Sie online oder laden Sie Bedienungsanleitung nach Für das Auto Draw-tite 40050 CLASS III-IV MULTI-FIT RECEIVER herunter. Draw-Tite 40050 CLASS III-IV MULTI-FIT RECEIVER User Manual Benutzerhandbuch

Inhaltsverzeichnis

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Für das Auto Draw-tite 40050 CLASS III-IV MULTI-FIT RECEIVER