Draw-tite 28501 INVISI-HITCH Bedienungsanleitung PDF herunterladen

Installation Instructions

Scion xB

Part Numbers:

28501

Hitch Shown In Proper Position

Wiring Access Location: SUV3, SUV4

Equipment Required:

Wrenches: 10mm, 14mm, 17mm

Drill Bits: None

1. Lower the exhaust by loosening rear two exhaust hangers.

2. Remove tie-down brackets as shown in FIGURE 1

. Return brackets and bolts to vehicle owner.

3. Remove and retain bolts from fascia tabs. See FIGURE 1

4. Raise hitch in place above the fascia tabs (not shown) and install fasteners into existing weld nuts in frame as shown in

FIGURE 2

5. Install the fascia tabs back onto the vehicle using the bolts that were retained from Step 3.

Rev. A05-08-0628501NSheet 1 of 3

z 2005 Cequent Towing Products

Spacer, 3/8” x 1-1/2” x 2”Qty. (2)

Conical Washer, 3/8”Qty. (4)

Bevel WasherQty. (4)

Hex Bolt, M10 x 1.25 x 40mmQty. (4)

Tighten all M10 CL8.8 fasteners with torque wrench to 42 Lb.-Ft (57 N-m).

Note: check hitch frequently, making sure all fasteners and ball are properly tightened. If hitch is removed, plug all holes in trunk pan or other body panels to

prevent entry of water and exhaust fumes. A hitch or ball which has been damaged should be removed and replaced. Observe safety precautions when working

beneath a vehicle and wear eye protection. Do not cut access or attachment holes with a torch.

This product complies with safety specifications and requirements for connecting devices and towing systems of the state of New York, V.E.S.C. Regulation V-5

and SAE J684.

2000 LB Max Gross Trailer Weight

200 LB Max Tongue Weight

Do Not Exceed Lower of Towing Vehicle

Manufacturer’s Rating or

Drawbar must be used in the

RISE

position only.

Drawbar Kit:

28451

Fastener Kit: 28501F

Adapter Kit:

28351

Frame Rail

Fascia

Tie-down

Brackets

Retain

Fasteners

Fascia Tabs

FIGURE 1

ALL FASTENERS TYPICAL BOTH SIDES

FIGURE 2

Frame Rail

Existing

Weld Nuts

1 2 3

Inhaltsverzeichnis

Seite 1 - Installation Instructions

Installation InstructionsScion xBPart Numbers:28501Hitch Shown In Proper PositionWiring Access Location: SUV3, SUV4Equipment Required:Wrenches: 10mm,

Seite 2 - Instructions d’installation

Instructions d’installationScion xBNuméros de pièces :28501Attelage montré dans la position appropriéePoints d’accès au câblage : SUV3, SUV4Équipement

Seite 3 - Instrucciones de instalación

Instrucciones de instalaciónScion xBNúmeros de partes:28501El enganche se muestra en la posición correctaUbicación del acceso al cableado: SUV3, SUV4E

Kommentare zu diesen Handbüchern

Keine Kommentare

Draw-tite 28501 INVISI-HITCH Bedienungsanleitung

Stöbern Sie online oder laden Sie Bedienungsanleitung nach Für das Auto Draw-tite 28501 INVISI-HITCH herunter. Draw-Tite 28501 INVISI-HITCH User Manual Benutzerhandbuch

Inhaltsverzeichnis

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Für das Auto Draw-tite 28501 INVISI-HITCH