Draw-tite 75681 MAX-FRAME RECEIVER Bedienungsanleitung PDF herunterladen

Installation Instructions

Part Numbers:

75681

87572

44637

Hitch Shown In Proper Position

Equipment Required:

Wrenches: 18mm, 19mm & 3/4

Saturn Vue: Open end 3/4 wrench,

Equinox: 6” Ratchet Extension

Drill Bits: None

1. If present, remove the tie down brackets from vehicle frame rail. Return bolts and tie down bracket to owner.

2. Remove the fascia door on the Equinox.

3. Feed the carriage bolt and large block thru slots on bottom of frame rails using the pull wire, as shown Figure 3

4. Raise the hitch into position; lifting the bumper mounting bracket over the fascia (where needed). Secure with M12 bolts and conical washers into

the existing weld nuts, being careful not to push the bolts into the frame, as shown Figure 1.

5. Hand tighten all bolts.

6. Saturn Vue:

Pull carriage bolts and small blocks thru end of the bumper and feed through the bumper mounting bracket using the pull wire.

Attach conical washer and nut. As shown Figure 1.

Chevrolet Equinox, Pontiac Torrent install the M12 bolts and conical washer through the bumper mounting bracket into the existing

weld nuts in the bumper, as shown Figure 2.

7. Tighten all 1/2-13 GR5 fastener with torque wrench to 75 Lb.-Ft. (102 N*M). Tighten all M12 CL10.9 fasteners with torque wrench to 92 Lb.-Ft.

(125 N*M)

8. Replace the fascia door on the Equinox.

Note: Due to different configuration of the vehicle there will be extra hardware left over.

Rev. A10-8-0975681NSheet 1 of 3

z 2009 Cequent Performance Products

Note: check hitch frequently, making sure all fasteners and ball are properly tightened. If hitch is removed, plug all holes in trunk pan or other body panels to

prevent entry of water and exhaust fumes. A hitch or ball which has been damaged should be removed and replaced. Observe safety precautions when working

beneath a vehicle and wear eye protection. Do not cut access or attachment holes with a torch.

This product complies with safety specifications and requirements for connecting devices and towing systems of the state of New York, V.E.S.C. Regulation V-5

and SAE J684.

Fastener Kit: 75681F

Do Not Exceed Lower of Towing Vehicle

Manufacturer’s Rating or

350 (159 Kg)3500 (1589 Kg)

Weight Carrying

Ball Mount

400 (182 Kg)4000 (1816 Kg)

Weight Distributing

Max Tongue

WT (LB)

Max Gross

Trailer WT (LB)

Hitch type

Wiring Access Location: 2005-06 Chevrolet SUV3

2007-09 Chevrolet SUV1, 2

06 Pontiac SUV3 07- Pontiac SUV1,2

Saturn SUV1, SUV2

2010 GMC & Terrain SUV1, 2

Fasteners typical both sides.

Bumper Mounting Bracket

Figure 2.

Existing Weld Nuts

Figure 1.

Pull Wire blocks

Frame Rail

Large Block

Pull Wire

See Step 3

Pull Wire

See Step 6

Existing Weld Nuts

Fascia

Bumper

Small Block

Figure 3.

Hex Nut 1/2-13Qty. (4)

Pull WireQty. (2)

Carriage Bolt 1/2-13Qty. (4)

Block 1-1/2 X 3 (Large Block)Qty. (2)

Conical WasherQty. (8)

Block 1-1/2 X 2 (Small Block)Qty. (2)

Hex Bolt M12Qty. (6)

Chevrolet Equinox

Pontiac Torrent

Saturn Vue

GMC Terrain

1 2 3

Inhaltsverzeichnis

Seite 1 - Installation Instructions

Installation InstructionsPart Numbers:75681 87572 44637Hitch Shown In Proper PositionEquipment Required:Wrenches: 18mm, 19mm & 3/4Saturn Vue: Open

Seite 2 - Instructions d’installation

Instructions d’installationNuméros de pièces :Attelage montré dans la position appropriéeÉquipement requis :Clés : 18 mm, 19 mm et 3/4Saturn Vue : Clé

Seite 3 - Instrucciones de instalación

Instrucciones de instalaciónNúmeros de partes:El enganche se muestra en la posición correctaEquipo necesario:Llaves: 18mm, 19mm y 3/4Saturn Vue: Llave

Kommentare zu diesen Handbüchern

Keine Kommentare

Draw-tite 75681 MAX-FRAME RECEIVER Bedienungsanleitung

Stöbern Sie online oder laden Sie Bedienungsanleitung nach Für das Auto Draw-tite 75681 MAX-FRAME RECEIVER herunter. Draw-Tite 75681 MAX-FRAME RECEIVER User Manual Benutzerhandbuch

Inhaltsverzeichnis

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Für das Auto Draw-tite 75681 MAX-FRAME RECEIVER