Draw-tite 118579 T-ONE CONNECTOR Bedienungsanleitung PDF herunterladen

9. Reconnect the vehicle’s Negative (-) battery

cable and install the 10 amp fuse into the fuse

holder from step 7.

WARNING

All connections must be complete for the Trailer

Tow Harness to function properly. Test and verify

installation with a test light or trailer once installed.

For initial test, reset vehicle electrical system by

temporarily removing the key from the ignition.

10. On the Driver’s side, mount the T-Connector

black box using the double-sided tape provided.

Secure the remainder of the T-Connector harness

with the cable ties provided, to prevent damage

or rattling and being careful to avoid any areas

that would cut or pinch the wire.

WARNING

Make sure module is mounted so that the epoxy

side of the module is pointed towards the ground

to prevent any water buildup.

11. Reinstall the taillight housing assemblies,

positioning the vehicle wiring harness between

the housing and the vehicle body.

12. Mount the 4-Flat end in an accessible location

with a bracket or electrical box (not included).

WARNING

Overloading circuit can cause fires. DO NOT

exceed lower of towing manufacturer rating or:

• Max. stop/turn light: 1 per side (2.1 amps)

• Max. tail lights: (5.6 amps)

Read vehicle’s owners manual & instruction sheet

for additional information.

ENGLISH

TOOLS REQUIRED:

Trim Panel Remover, Philips Head Screwdriver,

Drill (3/32” Drill Bit), 10mm socket or Wrench,

1/4” Socket, Test-probe

1. Open the tailgate to remove the vehicle’s

taillight assemblies. Starting on the driver’s side,

using a 10mm socket, carefully unscrew the

2 screws holding taillight in place. Carefully pry

the housing away from the vehicle, being careful

not to break the alignment tabs. Repeat on the

passenger side

2. On the driver and passenger sides of the vehicle,

locate the vehicle’s taillight wiring harness. The

taillight wiring harness will have a connection

point, on both sides, matching the ends of the

T-Connector. Separate this connector, being

careful not to break the locking tabs. All connector

surfaces should be clean and free of dirt

3. On the driver’s side, insert the T-Connector

end, with the yellow wire, between the vehicle

wiring connectors and lock into place. Be careful

not to damage the locking tabs and be sure that

connectors are fully inserted with locking tabs

in place.

4. Route the harness containing the green wire

and the 4-Flat down the opening behind the

taillight on the driver’s side. Route the 4-Flat

harness underneath and to the center of the

vehicle. Route harness containing the green

wire underneath the vehicle up through the

opening behind the passenger’s side taillight.

WARNING

Route the wire being careful to avoid any hot pipes,

heat shields, the fuel tank or any other points that

may pinch or break the wire.

5. Repeat step 3 for the passenger’s side using

the T-Connector containing the green wire.

6. Locate a suitable grounding point on the driver’s

side near the connectors. Drill a 3/32” hole and

secure white wire with eyelet using screw

provided. Do not drill into any exposed surfaces.

CAUTION

Verify what is behind any surface prior to drilling

to avoid damage to the vehicle and/or personal

injury. Do not drill into any exposed surfaces.

7. Disconnect the vehicle’s Negative (-) battery cable.

If not removed, remove the fuse from the yellow

fuse holder (provided). After cutting the fuse holder

wire

, attach the ring terminal and secure to the

vehicle’s Positive (+) battery cable. Connect the

other end of the fuse holder to the black 12 ga.

wire, using the yellow butt connector (provided)

WARNING

Read and follow all warnings and cautions printed

on the tow vehicle’s battery.

8. Route the black wire out of the engine

compartment and to the rear driver’s side of the

vehicle

. Connect the other end of the black

12 ga. wire to the red power wire located on the

T-Connector’s black box, using the yellow butt

connector (provided).

WARNING

Route the wire being careful to avoid any hot

pipes, heat shields, the fuel tank or any other

points that may pinch or break the wire.

READ THIS FIRST:

Read and follow all vehicle warnings and installation

instructions before beginning installation. Wear safety

glasses and use all safety precautions during installation.

LISEZ CECI EN PREMIER:

Lire et observer toutes les consignes de sécurité et

les instructions avant de commencer l’installation.

Durant l’installation, veiller à toujours porter des lunettes

de protection et respecter les mesures de sécurité.

LEA ESTO PRIMERO:

Lea y siga todas las advertencias e instrucciones de

instalación del vehículo antes de empezar la instalación.

Use gafas de seguridad y todas las precauciones de

seguridad durante la instalación.

118579-037 Rev. A 2/12/2013

Installation Instructions

Directives de Montage

Instrucciones de Instalación

T-Connector

Connecteur en T

Conector en T

Chevrolet

Traverse

GMC AcadiaBuick Enclave

ie f

1 2

Inhaltsverzeichnis

Seite 1 - GMC AcadiaBuick Enclave

9. Reconnect the vehicle’s Negative (-) battery cable and install the 10 amp fuse into the fuse holder from step 7. WARNING All connections must

Seite 2 - FraNçaIS

FraNçaISOUTILS REQUIS: Écarteur de panneau de garnisage, Tournevis à pointe cruciforme, Perceuse (mèche de 3/32 po), Douille ou clé 10 mm, Douille 1/4

Kommentare zu diesen Handbüchern

Keine Kommentare

Draw-tite 118579 T-ONE CONNECTOR Bedienungsanleitung

Stöbern Sie online oder laden Sie Bedienungsanleitung nach Für das Auto Draw-tite 118579 T-ONE CONNECTOR herunter. Draw-Tite 118579 T-ONE CONNECTOR User Manual Benutzerhandbuch

Inhaltsverzeichnis

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Für das Auto Draw-tite 118579 T-ONE CONNECTOR