WARNING
Read and follow all warnings and cautions
printed on the tow vehicle’s battery.
All connections must be complete for the
T-Connector to function properly. Test and
verify installation with a test light or trailer
once installed. For initial test, reset vehicle
electrical system by temporarily removing
the key from the ignition.
9. Secure the remainder of the T-Connector
harness with the cable ties provided, to prevent
damage or rattling and being careful to avoid
any areas that would pinch, cut or melt the wire.
10. Reinstall the plastic trim panels, threshold,
storage covers, floor covering and other items
that may have been removed during installation,
being careful not to pinch or cut the wires
NOTE
Store 4-Flat in trunk area when not in use.
WARNING
Overloading circuit can cause fires.
DO NOTexceed lower of vehicle manufacturer
rating or:
• Max. stop/turn light: 1 per side (2.1 amps)
• Max. tail lights: (5.6 amps)
Read vehicle’s owners manual & instruction
sheet for additional information.
ENGLISH
TOOLS REQUIRED:
Trim Panel Remover, Drill (3/32” Drill Bit),
1/4” Socket, Wire Crimpers, Wire Cutters,
Philips Head Screwdriver, Test-probe
1. Open the rear door of the vehicle and
temporarily remove the rear threshold,
cargo net and cargo cover to allow access
of the rear interior trim panel
d
.
NOTE
It may be helpful to fold rear seat forward.
2. Partially remove the rear interior trim panels
on both the driver and passenger side of the
vehicle. Several trim panel fasteners will need to
be removed to partially remove the panels
e
.
3. Behind the taillights, there will be connection
points matching the ends of the T-Connector
adapter on the back of each of the vehicle
taillight housings. Beginning on the driver’s
side, separate the vehicle’s wiring connectors,
being careful not to break the locking tabs.
Attach both ends of the T-Connector containing
the yellow and brown wires. Be careful not
to damage the locking tabs and be sure that
connectors are fully inserted with locking
tabs in place.
4. Route the T-Connector containing the
green wire below the threshold cover to
the passenger’s side taillight housing.
Repeat step 3 using the T-Connector end
containing the green wire.
5.
Locate a suitable grounding point on the driver’s
side near the connectors. Drill a 3/32” hole
and secure white wire with eyelet using screw
provided. Do not drill into any exposed surfaces.
CAUTION
Verify what is behind any surface prior to
drilling to avoid damage to the vehicle and/
or personal injury. Do not drill into any
exposed surfaces.
6. On the Driver’s side, mount the T-Connector
black box using the double-sided tape provided.
7. From inside the vehicle, connect the black
12 ga. wire and the black wire from the
T-Connector black box with the supplied
yellow butt connector. Either route the black
wire thru a grommet and along the exterior
frame or follow the existing wiring along the
thresholds into the engine compartment up to
the battery avoiding areas that may pinch or
break the wire
f
.
WARNING
If routing the wire thru a grommet and along
the exterior of the vehicle, be careful to avoid
any hot pipes, heat shields, the fuel tank or any
other points that may pinch or break the wire.
8. Disconnect the vehicle’s negative (-) battery
cable. If not removed, remove the fuse from the
yellow fuse holder (provided). After cutting the
fuse holder wire
g
, attach the ring terminal
and secure to the vehicle’s Positive (+) battery
cable
h
. Connect the other end of the fuse
holder to the black 12 ga. wire, using the
yellow butt connector (provided).
READ THIS FIRST:
Read and follow all vehicle warnings and installation
instructions before beginning installation. Wear safety
glasses and use all safety precautions during installation.
LISEZ CECI EN PREMIER:
Lire et observer toutes les consignes de sécurité et
les instructions avant de commencer l’installation.
Durant l’installation, veiller à toujours porter des lunettes
de protection et respecter les mesures de sécurité.
LEA ESTO PRIMERO:
Lea y siga todas las advertencias e instrucciones de
instalación del vehículo antes de empezar la instalación.
Use gafas de seguridad y todas las precauciones de
seguridad durante la instalación.
118575-037 Rev. A 11/30/2012
Installation Instructions
Directives de Montage
Instrucciones de Instalación
T-Connector
Connecteur en T
Conector en T
Spark
h
g
f
e
d
(2 Seiten)
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Kommentare zu diesen Handbüchern