Draw-tite 118407 T-ONE CONNECTOR Bedienungsanleitung PDF herunterladen

4. Locate a suitable grounding point near the

connector. (Do not drill into vehicle floor or

bed.) Clean dirt and rustproofing from

area. Drill a 3/32" hole and secure

white

wire using eyelet and screw provided.

CAUTION

Verify what is behind any surface prior

to drilling to avoid damage to the vehicle

and/or personal injury. Do not drill into

any exposed surfaces.

WARNING

All connections must be complete for the

T-Connector to function properly. Test and

verify installation with a test light or trailer

once installed.

5. Secure the remainder of the T-Connector

harness with the cable ties provided, to

prevent damage or rattling and being

careful to avoid any areas that would

pinch, cut or melt the wire.

6. Replace both foam insulation padding,

wiring access panels, cargo tray, spare

tire hold down nut, & cargo floor panel

removed during installation.

NOTE

Store 4-Flat connector in rear cargo

area when not in use.

WARNING

Overloading circuit can cause fires.

DO NOT exceed lower of vehicle

manufacturer rating or:

• Max. stop/turn light: 7.5 amps per side

• Max. tail lights: 7.5 amps

Read vehicle's owners manual &

instruction sheet for additional information.

ENGLISH

Tools Recommended:

Drill (3/32” Drill Bit), Philips Head

Screwdriver, Trim Panel Remover

1. Locate the vehicle wiring inside the

vehicle's rear cargo area by removing

both of the wiring access side panels

def

. Carefully remove the foam

insulation padding on each side to access

the taillight connection points

. There will

be connection points matching the ends of

the T-Connector adapter behind each of

the vehicle taillight housings

NOTE

There are two sets of taillight connection

points. Use the top set of connection

points for the T-Connector.

2. Beginning on the driver’s side, separate

the vehicle's wiring connectors, being

careful not to break the locking tabs.

All connector surfaces should be clean

and free of dirt. Attach each end of the

T-Connector containing the

yellow wire.

Ensure that the connectors are fully

inserted with locking tabs in place.

3. Pull up the cargo floor panel, and remove

the cargo tray by unscrewing the spare tire

hold down nut. Pull out cargo tray and set

aside. Route the T-Connector containing

the

green wire behind and under the trim

panel, along the vehicle floor near the

spare tire

. Continuing, route wire across

the vehicle and behind the trim panel and

up to the wiring access area. Repeat

step 2 for the passenger’s side using the

T-Connector containing the

green wire.

18407-037 Rev. A 08/18/05

READ THIS FIRST:

Read and follow all instructions carefully

before beginning installation.

LISEZ CECI EN PREMIER:

Lire et suivre toutes les instructions

attenrivement avant le montage.

LEA ESTO PRIMERO:

Lea y siga todas las instrucciones

cuidadosamente antes de iniciar la instalación.

•

Installation Instructions

Directives de Montage

Instrucciones de Instalación

T-Connector

Connecteur en T

Conector en T

1 2

18407-037 Rev. A 08/18/05 1

Inhaltsverzeichnis

Seite 1 - 18407-037 Rev. A 08/18/05

4. Locate a suitable grounding point near theconnector. (Do not drill into vehicle floor orbed.) Clean dirt and rustproofing fromarea. Drill a 3/32&qu

Seite 2

ESPAÑOLHERRAMIENTAS NECESSARIAS:Taladro (broca de 3/32"), Destornillador de estrella, Corte el removedor de paneles 1. Encuentre los cables del

Kommentare zu diesen Handbüchern

Keine Kommentare

Draw-tite 118407 T-ONE CONNECTOR Bedienungsanleitung

Stöbern Sie online oder laden Sie Bedienungsanleitung nach Für das Auto Draw-tite 118407 T-ONE CONNECTOR herunter. Draw-Tite 118407 T-ONE CONNECTOR User Manual [de] [fr] [it] Benutzerhandbuch

Inhaltsverzeichnis

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Für das Auto Draw-tite 118407 T-ONE CONNECTOR