Draw-tite 118419 T-ONE CONNECTOR Bedienungsanleitung PDF herunterladen

5. Locate a suitable grounding point near

the connector. Clean dirt and rustproofing

from the area. Drill a 3/32" hole and

secure the white wire using the eyelet

and screw provided.

CAUTION

Verify what is behind any surface prior to

drilling to avoid damage to the vehicle and/

or personal injury. Do not drill into any

exposed surfaces.

WARNING

All connections must be complete for the

T-Connector to function properly. Test and

verify installation with a test light or trailer

once installed.

6. Route the 4-Flat from below the threshold

plate into trunk. Store there when not in use.

7. Reinstall felt trunk liner, threshold, and other

items removed during installation, being

careful not to pinch or cut the wires.

WARNING

Overloading circuit can cause fires. DO

NOT exceed lower of towing manufacturer

rating or:

• Max. stop/turn light: (7.5 amps)

• Max. tail lights: (7.5 amps)

Read vehicle's owners manual & instruction

sheet for additional information.

ENGLISH

TOOLS NEEDED

Trim Panel Remover

1. Open trunk. Temporarily remove the rear

threshold plate

. Partially remove the

felt trunk liner behind the taillights

2. On the driver and passenger sides of the

vehicle, locate the vehicle's taillight wiring

harness

. The taillight wiring harness

will have a connection point, on both

sides, matching the ends of the T-Connector.

Separate this connector, being careful not

to break the locking tabs. All connector

surfaces should be clean and free of dirt.

3. On the driver's side, insert the T-Connector

end, with the

yellow wire, between the

vehicle wiring connectors and lock into

place. Be careful not to damage the locking

tabs and be sure that connectors are fully

inserted with locking tabs in place.

4. Route the T-Connector end with green

wire to the passenger 's side behind the

panels and along the threshold. Repeat step

3 using the T-Connector ends containing the

green wire.

118419-037 Rev. A 10/04/06

•

READ THIS FIRST:

Read and follow all vehicle warnings and

installation instructions before beginning

installation. Wear safety glasses and use

all safety precautions during installation.

LISEZ CECI EN PREMIER:

Lire et observer toutes les consignes de sécurité

et les instructions avant de commencer l’installa-

tion. Durant l’installation, veiller à toujours porter

des lunettes de protection et respecter les

mesures de sécurité.

LEA ESTO PRIMERO:

Lea y siga todas las advertencias e instrucciones

de instalación del vehículo antes de empezar la

instalación. Use gafas de seguridad y todas las

precauciones de seguridad durante la instalación.

Installation Instructions

Directives de Montage

Instrucciones de Instalación

T-Connector

Connecteur en T

Conector en T

1 2

FRANÇAIS 2

Inhaltsverzeichnis

Seite 1

5. Locate a suitable grounding point near the connector. Clean dirt and rustproofingfrom the area. Drill a 3/32" hole and secure the white wire u

Seite 2 - FRANÇAIS

FRANÇAISOUTILS REQUIS :Écarteur de panneau de garnisage1. Ouvrir le coffre d. Enlever temporairement le panneau de seuil arrière. Retirer partiellemen

Kommentare zu diesen Handbüchern

Keine Kommentare

Draw-tite 118419 T-ONE CONNECTOR Bedienungsanleitung

Stöbern Sie online oder laden Sie Bedienungsanleitung nach Für das Auto Draw-tite 118419 T-ONE CONNECTOR herunter. Draw-Tite 118419 T-ONE CONNECTOR User Manual Benutzerhandbuch

Inhaltsverzeichnis

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Für das Auto Draw-tite 118419 T-ONE CONNECTOR