Draw-tite 24904 SPORTFRAME HITCH Bedienungsanleitung PDF herunterladen

Hitch Shown In Proper Position

Equipment Required:

Wrenches: 13mm, 18mm, ¾”

Drill Bits: None

1. Lower exhaust as follows:

On driver’s side, disconnect rubber exhaust hanger forward of muffler. (Lubricating Spray Recommended)

On passenger’s side, remove exhaust hanger bracket by removing (2) M8 fasteners. Discard M8 fasteners.

2. On driver’s side, bend or cut heat shield to expose hole in frame rail.

3. Fishwire carriage bolts and spacer blocks up thru access holes in each frame rail and down thru attaching holes as shown above.

See figure 3.

Note: On both sides, at access hole in vehicle frame, refer to figure 2 to reverse fishwire block and bolt up thru large slot and back

down thru same slot.

4. On driver’s side, remove existing M12 bolt at forward most attachment and retain for hitch installation (Do not clean threads).

5. Raise hitch into position, being careful not to push bolts back into frame. Loosely attach with conical toothed washers and nuts.

6. Align holes in hitch with holes in vehicle. Install remaining fasteners as shown above and tighten.

Tighten all ½-13 GR5 fasteners with torque wrench to 75 Lb.-Ft. (102 N*M)

Qty. (3) Carriage Bolt – ½-13 x 1.75 GR5

Qty. (3) Hex Nut – ½-13

Qty. (3) Spacer Block ¼ x 1 x 3

Qty. (2) Hex Bolt Ass’y M8 x 1.25 x 35mm CL9.8

Qty. (3) Conical Toothed Washer – ½”

Tighten all M8 x 1.25 CL9.8 fasteners with torque wrench to 20 Lb.-Ft. (27 N*M)

Drawbar must be used in the

Rise position only.

Drawbar Kit:

3594

Fastener Kit: 24904F

Tighten all M12 x 1.50 CL10.9 fasteners with torque wrench to 92 Lb.-Ft. (125 N*M)

A. Insert bolt and

Block into frame

B. Align block on

access hole

C. Pull bolt thru

block

Figure 2

Reverse Fishwiring procedure

Figure 3

Kink pull wire to keep

Spacer independent of bolt

Figure 1

Exhaust hanger bracket

On passenger’s side

Existing

M12 Flanged

Hex bolt

Existing

Weldnut

Vehicle

Frame

Bend or cut

Heat shield to

Expose this hole

Installation Instructions

Volkswagen GTI

Volkswagen Golf GTI (Canada Only)

Part Numbers:

24904

60330

77291

Wiring Access Location: PC3, 4

z 2012 Cequent Performance Products, Inc.

Sheet 1 of 3 24904N 11-19-12

Rev. A

Note: check hitch frequently, making sure all fasteners and ball are properly tightened. If hitch is removed, plug all holes in trunk pan or other body panels to

prevent entry of water and exhaust fumes. A hitch or ball which has been damaged should be removed and replaced. Observe safety precautions when working

beneath a vehicle and wear eye protection. Do not cut access or attachment holes with a torch.

This product complies with safety specifications and requirements for connecting devices and towing systems of the state of New York, V.E.S.C. Regulation V-5

and SAE J684.

Do Not Exceed Lower of Towing Vehicle

Manufacturer’s Rating or

2000 LB (908 Kg) Max Gross Trailer Weight

200 LB (90.8 Kg) Max Tongue Weight

Form F206 Rev B 9-17-2012

Accessory Rating

Access Holes

1 2 3

Volkswagen GTI 1

Inhaltsverzeichnis

Seite 1 - Volkswagen GTI

Hitch Shown In Proper Position Equipment Required: Wrenches: 13mm, 18mm, ¾” Drill Bits: None 1. Lower exhaust as follows: On driver’s side, disco

Seite 2

Instructions d’installation Numéros de pièces : Points d’accès au câblage : PC3, 4 z 2012 Cequent Performance Products, Inc. Feuille 2 de 3 24904N

Seite 3

Instrucciones de instalación Números de partes: Ubicación del acceso al cableado: PC3, 4 z 2012 Cequent Performance Products, Inc. Hoja 3 of 3 249

Kommentare zu diesen Handbüchern

Keine Kommentare

Draw-tite 24904 SPORTFRAME HITCH Bedienungsanleitung

Stöbern Sie online oder laden Sie Bedienungsanleitung nach Für das Auto Draw-tite 24904 SPORTFRAME HITCH herunter. Draw-Tite 24904 SPORTFRAME HITCH User Manual Benutzerhandbuch

Inhaltsverzeichnis

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Für das Auto Draw-tite 24904 SPORTFRAME HITCH