Draw-tite 24911 SPORTFRAME HITCH Bedienungsanleitung PDF herunterladen

Installation Instructions

Toyota Yaris Hatchback

Part Numbers:

24911

60343

77298

Hitch Shown In Proper Position

Wiring Access Location: PC3, 4

Equipment Required: Pliers, small flat screwdriver

Wrenches: 9/16” open end wrench,

11/16” & two 15/16”

Drill Bits: None



1. Locate a tab at the bottom center of the trunk pan, bend down and out of the way.

2. Remove the (2) plastic rivets that fasten the fascia tabs to the vehicle. Note: Remove the center of the rivet with a flat screwdriver. Keep for re-

installation.

3. Raise hitch into position passenger side first. Slide hitch under the fascia tab and over the top of the exhaust being careful not to scratch the

fascia.

4. Slide the hitch under the fascia tab on the drivers side and into location between the vehicle’s tie down brackets.

5. Install the 5/8 bolts and flat washer to the outside of the tie down bracket, both sides as shown. Attach the lock washers and hex nuts. (Do not

tighten at this time.)

6. Install remaining fasteners as shown, both sides.

7. Tighten all fasteners to the required torque specification.

8. Re-install the plastic rivets.

z 2013 Cequent Performance Products

Sheet 1 of 3 24911N 11-13-13 Rev. A



Qty. (2) Bolt 5/8-11 X 2.0 GR8



Qty. (4) Bolt 3/8-16 X 1.50 Gr8



Qty. (2) Flat washer 5/8”



Qty. (4) Lock washer 3/8”



Qty. (2) Lock washer 5/8”



Qty. (4) Hex nut 3/8-16



Qty. (2) Hex nut 5/8-11

Tighten all 5/8-11 Gr8 fasteners with torque wrench to 212 Lb.-Ft. (287 N*M)

Tighten all 3/8-16 Gr8 fasteners with torque wrench to 45 Lb.-Ft. (61 N*M)

Note: check hitch frequently, making sure all fasteners and ball are properly tightened. If hitch is removed, plug all holes in trunk pan or other body panels to prevent

entry of water and exhaust fumes. A hitch or ball which has been damaged should be removed and replaced. Observe safety precautions when working beneath a

vehicle and wear eye protection. Do not cut access or attachment holes with a torch.

This product complies with safety specifications and requirements for connecting devices and towing systems of the state of New York, V.E.S.C. Regulation V-5 and

SAE J684.

Do Not Exceed Lower of Towing Vehicle

Manufacturer’s Rating or

Drawbar must be used in the

RISE position only.

Drawbar Kit:

3593

Fastener Kit: 24911F

Form F206 Rev B 9-17-2012

Accessory Rating

2000 LB (908 Kg) Max Gross Trailer Weight

200 LB (90.8 Kg) Max Tongue Weight

Printed in Mexico















Note: Fasteners typical

both sides

Bend tab down out of

the way – as shown

Vehicle tie down

bracket – both sides

Vehicle tie

down bracket

Fascia





1 2 3

Inhaltsverzeichnis

Seite 1 - Installation Instructions

Installation Instructions Toyota Yaris Hatchback Part Numbers: 24911 60343 77298 Hitch Shown In Proper Position Wiring Access Location: PC3, 4 Equipm

Seite 2 - Instructions d’installation

Instructions d’installation Toyota Yaris Hatchback Numéros de pièce : 24911 60343 77298 Attelage montré dans la position appropriée Points d'acc

Seite 3 - Instrucciones de instalación

Instrucciones de instalación Toyota Yaris Hatchback Números de partes: 24911 60343 77298 El enganche se muestra en la posición correcta Ubicación del

Kommentare zu diesen Handbüchern

Keine Kommentare

Draw-tite 24911 SPORTFRAME HITCH Bedienungsanleitung

Stöbern Sie online oder laden Sie Bedienungsanleitung nach Für das Auto Draw-tite 24911 SPORTFRAME HITCH herunter. Draw-Tite 24911 SPORTFRAME HITCH User Manual Benutzerhandbuch

Inhaltsverzeichnis

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Für das Auto Draw-tite 24911 SPORTFRAME HITCH