Draw-tite 24847 SPORTFRAME HITCH Bedienungsanleitung PDF herunterladen

Installation Instructions

Toyota Prius - all models

Toyota Prius V - all models

Part Numbers:

Hitch Shown In Proper Position

Wiring Access Location:

Equipment Required: 6- 8” Ratchet Extension

Wrenches: 17mm, 19mm

Frame

rail

Do Not Exceed Lower of Towing Vehicle

Manufacturer’s Rating or

Drawbar must be used in the

Rise position only.

Drawbar Kit:

3598

Fastener Kit: 24847F

2000 LB (908 Kg) Max Gross Trailer Weight

200 LB (90.8 Kg) Max Tongue Weight

Appearance

panel

Prius only

Fascia

Prius

Frame

rail

Tie down bracket opening

on appearance panel

Existing

weldnuts

Exhaust

hanger

bracket

Note: Fasteners typical

both sides

Appearance panel

(Prius only)

shown

off vehicle

Tie down

bracket opening

Appearance panel not shown

24847, 60263,

77220, 24796 (U-Haul)

Fascia

Prius V

1. Remove the tie-down hook on driver’s side. Note: remove the bolts leaving the appearance panel in

place, (Prius only). Return tie-down hook and fasteners to vehicle owner.

2. Lower exhaust system at the rubber isolator leaving the rubber isolator in place on the exhaust. Note:

Spraying a lubricant or soapy water on the metal hanger rod and the rubber isolator helps removal. Be

careful not to allow muffler to fall under its own weight.

3. Remove (2) fasteners holding rear muffler hanger. Return fasteners to owner.

4. Raise the driver’s side of the hitch into position through the tie-down bracket opening. With the

passengers side on the ground rotate the hitch through the cut-out. Leave hitch supported (jack, blocks,

person).

5. Raise the passengers side of the hitch over the tail pipe, sandwiching bracket between the frame rail and

exhaust hanger bracket. Loosely install fasteners.

6. Install remaining fasteners as shown.

7. Tighten all fasteners to the required torque specification.

8. Reinstall exhaust.

Tighten all M12 CL8.8 fasteners with torque wrench to 65 Lb.-Ft. (88 N*M)

Qty. (4) Hex bolt M12 X 1.25 X 35 CL8.8

Qty. (4) Conical washer 1/2”

Note: check hitch frequently, making sure all fasteners and ball are properly tightened. If hitch is removed, plug all holes in trunk pan or other body panels to

prevent entry of water and exhaust fumes. A hitch or ball which has been damaged should be removed and replaced. Observe safety precautions when working

beneath a vehicle and wear eye protection. Do not cut access or attachment holes with a torch.

This product complies with safety specifications and requirements for connecting devices and towing systems of the state of New York, V.E.S.C. Regulation V-5

and SAE J684.

Form F206 Rev A 5605

shown

off vehicle

Appearance panel not shown

installation view for clarity

1 2 3

Inhaltsverzeichnis

Seite 1 - Installation Instructions

Installation InstructionsToyota Prius - all models Toyota Prius V - all modelsPart Numbers:Hitch Shown In Proper PositionWi

Seite 2 - Instructions d’installation

Instructions d’installationNuméros de pièces :Attelage montré dans la position appropriéePoints d’accès au câblage : Équipement requis : Rallonge de

Seite 3 - Instrucciones de instalación

Instrucciones de instalación Toyota Prius - todos los modelosNúmeros de partes:El enganche se muestra en la posición correcta Ubicación del acceso al

Kommentare zu diesen Handbüchern

Keine Kommentare

Draw-tite 24847 SPORTFRAME HITCH Bedienungsanleitung

Stöbern Sie online oder laden Sie Bedienungsanleitung nach Für das Auto Draw-tite 24847 SPORTFRAME HITCH herunter. Draw-Tite 24847 SPORTFRAME HITCH User Manual [en] Benutzerhandbuch

Inhaltsverzeichnis

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Für das Auto Draw-tite 24847 SPORTFRAME HITCH