Draw-tite 118531 T-ONE CONNECTOR Bedienungsanleitung PDF herunterladen

WARNING

The black box-module is intended to be mounted

ONLY in the INTERIOR of the vehicle. Mounting on

the exterior or areas exposed to the elements or

moisture could cause serious damage to the vehicle

and module. Secure the remainder of the T-Connector

harness with the cable ties provided, to prevent

damage or rattling and being careful to avoid any

areas that would pinch, cut or melt the wire.

WARNING

All connections must be complete for the T-Connector

to function properly. Test and verify installation with a

test light or trailer once installed. For initial test, reset

vehicle electrical system by temporarily removing the

key from the ignition. Re-insert key and turn key to

the proper position.

11. Replace the trunk threshold panel, floor coverings

and felt trunk liner removed during installation.

NOTE

Store 4-Flat in rear cargo area when not in use.

WARNING

Overloading circuit can cause fires. DO NOT exceed

lower of vehicle manufacturer rating or:

• Max. stop/turn light: 2 per side (4.2 amps)

• Max. tail lights: (7.5 amps)

Read vehicle’s owners manual & instruction sheet

for additional information.

118531-037 Rev. A 03/02/11

ENGLISH

TOOLS NEEDED:

Trim Panel Remover, 10mm Socket &

Ratchet or 10mm Wrench, Drill (3/32” Drill Bit),

1/4” Socket, Wire Crimpers, Wire Cutters,

Philips Head Screwdriver, Test-probe

1. Open trunk and remove threshold panel. Partially

remove the corner felt trunk liner, on both sides,

exposing the vehicle’s taillight wiring harness

2. On the driver and passenger sides of the vehicle,

locate the vehicle’s taillight wiring harness. The

taillight wiring harness will have a connection point,

on both sides, matching the ends of the T-Connector.

Separate this connector, being careful not to break

the locking tabs. All connector surfaces should be

clean and free of dirt

3. On the driver’s side, insert the T-Connector end,

with the yellow wire, between the vehicle wiring

connectors and lock into place. Be careful not to

damage the locking tabs and be sure that connectors

are fully inserted with locking tabs in place.

4. Route the T-Connector end, with the green wire,

under felt trunk liner to passenger side vehicle

taillight wiring harness.

Repeat step 3 for the passenger’s side using the

T-Connector containing the green wire.

5. Locate a suitable grounding point on the driver’s side

near the connectors. Drill a 3/32” hole and secure

white wire with eyelet using screw provided. Do not

drill into any exposed surfaces.

CAUTION

Verify what is behind any surface prior to drilling to

avoid damage to the vehicle and/or personal injury.

Do not drill into any exposed surfaces.

6. On the driver’s side, locate the red 12 ga.

Power wire from the T-Connector. Attach the

black 12 ga. wire provided.

Route the black wire along the exterior frame or

follow the existing wiring along the thresholds into

the engine compartment up to the battery avoiding

areas that may pinch or break the wire

7. Disconnect the vehicle’s Negative (-) battery cable.

If not removed, remove the fuse from the yellow fuse

holder (provided). After cutting the fuse holder wire,

attach the ring terminal and secure to the vehicle’s

Positive (+) battery cable. Connect the other end of

the fuse holder to the black 12 ga. wire, using the

yellow butt connector (provided)

WARNING

Read and follow all warnings and cautions printed

on the tow vehicle’s battery.

8. Reconnect the vehicle’s Negative (-) battery cable

and install the 15 amp fuse into the fuse holder

from step 7.

9. Locate the T-Connector’s Grey 12-Pin connector

and insert it into the mating connector located

on the black box-module. Check to see that the

mating surfaces of the wiring connectors match.

All connector surfaces should be clean and free of

dirt. Be careful not to damage the locking tabs and

be sure that connectors are fully inserted with

locking tabs in place

10. Locate a flat surface in an out of the way place

and mount the T-Connector’s black box-module,

to prevent damage or rattling.

NOTE

This surface should be in an area that is free of

any moisture and mounted in an area that it is high

enough where it could not be exposed to direct

contact with any water or liquid substance.

Jetta Sedan

READ THIS FIRST:

Read and follow all vehicle warnings and installation

instructions before beginning installation. Wear safety

glasses and use all safety precautions during installation.

LISEZ CECI EN PREMIER:

Lire et observer toutes les consignes de sécurité et les

instructions avant de commencer l’installation. Durant

l’installation, veiller à toujours porter des lunettes de

protection et respecter les mesures de sécurité.

LEA ESTO PRIMERO:

Lea y siga todas las advertencias e instrucciones de

instalación del vehículo antes de empezar la instalación.

Use gafas de seguridad y todas las precauciones de

seguridad durante la instalación.

Installation Instructions

Directives de Montage

Instrucciones de Instalación

T-Connector

Connecteur en T

Conector en T

1 2

118531-037 Rev. A 03/02/11 1

Inhaltsverzeichnis

Seite 1 - 118531-037 Rev. A 03/02/11

WARNINGThe black box-module is intended to be mounted ONLY in the INTERIOR of the vehicle. Mounting on the exterior or areas exposed to the elem

Seite 2

FraNçaISOUTILS REQUIS: Écarteur de panneau de garnisage, Cliquet et douille de 10 mm ou clé de 10 mm, Perceuse (mèche de 3/32 po), Douille 1/4 po, Ser

Kommentare zu diesen Handbüchern

Keine Kommentare

Draw-tite 118531 T-ONE CONNECTOR Bedienungsanleitung

Stöbern Sie online oder laden Sie Bedienungsanleitung nach Für das Auto Draw-tite 118531 T-ONE CONNECTOR herunter. Draw-Tite 118531 T-ONE CONNECTOR User Manual Benutzerhandbuch

Inhaltsverzeichnis

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Für das Auto Draw-tite 118531 T-ONE CONNECTOR