8. Reconnect the vehicle’s Negative (-) battery
cable and install the 10 amp fuse into the
fuse holder from step 9.
WARNING
All connections must be complete for the
T-One
®
T-Connector to function properly.
Test and verify installation with a test light
or trailer once installed. For initial test, reset
vehicle electrical system by temporarily
removing the key from the ignition.
9. On the passenger’s side, mount the T-One
®
T-Connector black box using the double-sided
tape provided. Secure the remainder of the
T-One
®
T-Connector harness with the cable
ties provided, to prevent damage or rattling
and being careful to avoid any areas that
would cut or pinch the wire.
10. Secure the remainder of the T-One
®
T-Connector harness with the cable ties
provided, to prevent damage or rattling and
being careful to avoid any areas that would
pinch, cut or melt the wire.
11. Reinstall taillight assemblies and other items
removed during installation, being careful not
to pinch or cut the wires.
WARNING
Overloading circuit can cause fires. DO NOT
exceed lower of vehicle manufacturer rating or:
• Max. stop/turn light: 1 per side (2.1 amps)
• Max. tail lights: (5.6 amps)
Read vehicle’s owners manual & instruction
sheet for additional information.
ENGLISH
TOOLS REQUIRED:
Trim Panel Remover, 10mm Socket & Ratchet
or 10mm Wrench, Drill (3/32” Drill Bit),
1/4” Socket, Wire Crimpers, Wire Cutters,
Philips Head Screwdriver, Test-probe
1. Open trunk/hatch
d
to locate the vehicle
wiring inside the vehicle’s rear cargo area
by partially removing the plastic threshold
cover, side access panels or carpet panels
and cargo trays
ef
.
2. On the driver and passenger sides of the
vehicle, locate the vehicle’s taillight wiring
harness. The taillight wiring harness will have
a connection point, on both sides, matching
the ends of the T-One
®
T-Connector. Separate
this connector, being careful not to break the
locking tabs. All connector surfaces should
be clean and free of dirt.
3. On the passenger side, insert the T-One
®
T-Connector end with the green wire between
the vehicle wiring connectors and lock into
place. Route the T-One
®
T-Connector end with
the yellow wire to the driver’s side behind the
panels and along the threshold. Repeat for
T-One
®
T-Connector end with the yellow wire.
4. On the passenger side locate a suitable
grounding point near the connector.
OPTION 1
Clean dirt and rustproofing from the area.
Drill a 3/32” hole and secure the white wire
using the eyelet and screw provided. (Do not
drill into vehicle floor or bed. Do not drill into
any exposed surfaces.)
OPTION 2
Locate existing ground stud. Loosen bolt,
place screw eyelet on stud and re-tighten bolt.
CAUTION
Verify what is behind any surface prior to
drilling to avoid damage to the vehicle and/
or personal injury. Do not drill into any
exposed surfaces.
5. On the passenger’s side, locate the red 12 ga.
Power wire from the T-Connector box. Attach
the black 12 ga. wire provided.
6. Locate the vehicle’s 12 Volt Battery inside the
cargo area on the passenger side, underneath
the floor covering in the rear corner
g
.
7. Disconnect the vehicle’s Negative (-)
battery cable. If not removed, remove the
fuse from the yellow fuse holder (provided).
After cutting the fuse holder wire
h
, attach
the ring terminal and secure to the vehicle’s
Positive (+) battery cable. Connect the other
end of the fuse holder to the black 12 ga. wire,
using the yellow butt connector (provided)
i
.
WARNING
Read and follow all warnings and cautions
printed on the tow vehicle’s battery.
Installation Instructions
Directives de Montage
Instrucciones de Instalación
T-One
®
T-Connector
T-One
®
Connecteur en T
T-One
®
Conector en T
Pruis V
118610-037 Rev. A 8/23/2013
READ THIS FIRST:
Read and follow all vehicle warnings and installation
instructions before beginning installation. Wear safety
glasses and use all safety precautions during installation.
LISEz CECI EN PREMIER:
Lire et observer toutes les consignes de sécurité et les
instructions avant de commencer l’installation. Durant
l’installation, veiller à toujours porter des lunettes de
protection et respecter les mesures de sécurité.
LEA ESTO PRIMERO:
Lea y siga todas las advertencias e instrucciones de
instalación del vehículo antes de empezar la instalación.
Use gafas de seguridad y todas las precauciones de
seguridad durante la instalación.
PAGE 1 OF 3
d
e
f g
h
i
(2 Seiten)
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Kommentare zu diesen Handbüchern