Draw-tite 118412 T-ONE CONNECTOR Bedienungsanleitung PDF herunterladen

ENGLISH

TOOLS REQUIRED:

Trim Panel Remover, Philips Head Screwdriver,

Drill (3/32” Drill Bit), 10mm and 12 mm Wrench

1. Open rear hatch. Temporarily remove the rear

threshold plate, privacy screen, storage covers

and floor covering

2. Partially remove the rear interior trim panels on

both the driver and passenger side of the vehicle

. Several trim panel fasteners will need to be

removed to remove the panels

. Set aside

all items removed being careful not

to damage parts.

3. On the driver and passenger sides of the vehicle,

locate the vehicle's taillight wiring harness.

NOTE: There are several connection points

similar to the T-One harness in the rear of the

vehicle. Locate the taillight wiring harness that

has a connection point on the rear of the

taillight assembly.

Separate this connector, being careful not to break

the locking tabs. All connector surfaces should be

clean and free of dirt.

4. On the driver’s side, attach each end of the

T-Connectors containing the yellow and the brown

wires. Ensure that the connectors are fully inserted

with locking tabs in place.

5. Route the T-Connector containing the green

wire below the threshold cover to the passenger’s

side taillight housing. Repeat step 4 using the

T-Connector ends containing the green wire.

6. On driver’s side, locate a flat surface in a out of

the way place and mount the T-Connector’s black

convertor box with the double sided tape.

118412-037 Rev. B 10/05/07

Installation Instructions

Directives de Montage

Instrucciones de Instalación

T-Connector

Connecteur en T

Conector en T

7. Locate a suitable grounding point near the

connector such as the vehicle's frame or cross

member. (Do not drill into vehicle floor or bed.)

Clean dirt and rustproofing from area. Drill a

3/32" hole and secure white wire using eyelet

and screw provided.

CAUTION Verify what is behind any surface

prior to drilling to avoid damage to the vehicle

and/or personal injury. Do not drill into any

exposed surfaces.

8. Secure all loose wires with cable ties. Secure the

remainder of the T-Connector harness with the

cable ties provided, to prevent damage or rattling

and being careful to avoid any areas that would

cut or pinch the wire.

NOTE: Route the 4-Flat through the driver's side

trim panel into side storage compartment and

store there when not in use. When in use pull

4-Flat through the door and close.

WARNING Be careful not to pinch harness

in door latch.

9. On the driver’s side, locate the red 12 ga. Power

wire from the T-Connector box. Attach the black

12 ga. wire provided.

10. Either route the black wire thru a grommet and

along the exterior frame or follow the existing

wiring along the thresholds into the engine

compartment up to the battery avoiding areas

that may pinch or break the wire

WARNING If routing the wire thru a grommet

and along the exterior of the vehicle, be careful to

avoid any hot pipes, heat shields, the fuel tank or

any other points that may pinch or break the wire.

11. Disconnect the vehicle's Negative (-) battery

cable. If not removed, remove the fuse from the

yellow fuse holder (provided). After cutting the

fuse holder wire, attach the ring terminal and

secure to the vehicle's Positive (+) battery cable

. Connect the other end of the fuse holder

to the black 12 ga. wire, using the yellow butt

connector (provided).

12. Reconnect the vehicle's Negative (-) battery

cable and install the 10 amp fuse into the

fuse holder.

WARNING All connections must be complete

for the T-Connector to function properly. Test

and verify installation with a test light or trailer

once installed.

13. Secure the remainder of the T-Connector

harness with the cable ties provided, to prevent

damage or rattling and being careful to avoid

any areas that would cut or pinch the wire.

14. Reinstall the plastic trim panels, threshold,

storage covers, floor covering and other items

removed during installation, being careful not

to pinch or cut the wires.

WARNING Overloading circuit can

cause fires. DO NOT exceed lower of

towing manufacturer rating or:

• Max. stop/turn light: 1 per side (2.1 amps)

• Max. tail lights: (4.2 amps)

Read vehicle's owners manual & instruction

sheet for additional information.

•

READ THIS FIRST:

Read and follow all vehicle warnings and installation instructions

before beginning installation. Wear safety glasses and use all

safety precautions during installation.

LISEZ CECI EN PREMIER:

Lire et observer toutes les consignes de sécurité et les instruc-

tions avant de commencer l’installation. Durant l’installation,

veiller à toujours porter des lunettes de protection et respecter

les mesures de sécurité.

LEA ESTO PRIMERO:

Lea y siga todas las advertencias e instrucciones de instalación

del vehículo antes de empezar la instalación. Use gafas de

seguridad y todas las precauciones de seguridad durante

la instalación.

1 2

FRANÇAIS 2

Inhaltsverzeichnis

Seite 1

ENGLISHTOOLS REQUIRED:Trim Panel Remover, Philips Head Screwdriver,Drill (3/32” Drill Bit), 10mm and 12 mm Wrench 1. Open rear hatch. Temporarily remo

Seite 2 - FRANÇAIS

7. Encuentre un punto de conexión a tierra adecua-do cerca del conector tal como la estructura delvehículo o el travesaño. (No perfore en el piso o ba

Kommentare zu diesen Handbüchern

Keine Kommentare

Draw-tite 118412 T-ONE CONNECTOR Bedienungsanleitung

Stöbern Sie online oder laden Sie Bedienungsanleitung nach Für das Auto Draw-tite 118412 T-ONE CONNECTOR herunter. Draw-Tite 118412 T-ONE CONNECTOR User Manual Benutzerhandbuch

Inhaltsverzeichnis

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Für das Auto Draw-tite 118412 T-ONE CONNECTOR