Draw-tite 36455 FRAME HITCH Bedienungsanleitung PDF herunterladen

Installation Instructions

Part Numbers:

90169

36455

06550

Hitch Shown In Proper Position

Equipment Required:

Wrenches: 13mm, 15mm, 18mm

Drill Bits: None

1. Lower exhaust by removing bolt which attaches rearmost hanger bracket to passenger’s side frame rail. Retain bolt for

reinstallation.

2. Snap plastic loom in place over Air Conditioning line on Passenger’s side near bolt if present. See Figure 2 above.

3. Remove existing bolts from frame rails as shown in Figure 2, (2) on driver’s side, (2) on passenger’s side and retain for hitch

installation.

4. Raise hitch into position as shown in Figure 1 and attach with existing bolts removed in step 2. Hand tighten.

5. Push hitch towards driver’s side, so that passenger’s side bracket is up against trunk pan, and tighten fasteners to

specifications below.

6. Raise exhaust back into position and reinstall bolt removed in step 1.

Note: Rotating exhaust hanger bracket before tightening will add clearance between side bracket and exhaust.

Tighten all M10 CL10.9 fasteners with torque wrench to 53 Lb.-Ft. (72 N*M)

Tighten all M12 CL10.9 fasteners with torque wrench to 92 Lb.-Ft. (125 N*M)

z2007, 2008, 2009 Cequent Towing Products

Sheet 1 of 3 36455N 8-4-09 Rev. E

Note: check hitch frequently, making sure all fasteners and ball are properly tightened. If hitch is removed, plug all holes in trunk pan or other body panels to

prevent entry of water and exhaust fumes. A hitch or ball which has been damaged should be removed and replaced. Observe safety precautions when working

beneath a vehicle and wear eye protection. Do not cut access or attachment holes with a torch.

This product complies with safety specifications and requirements for connecting devices and towing systems of the state of New York, V.E.S.C. Regulation V-5

and SAE J684.

Fastener Kit: 36455F

Do Not Exceed Lower of Towing Vehicle

Manufacturer’s Rating or

Hitch type

Max Gross

Trailer WT (LB)

Max Tongue

WT (LB)

Weight Carrying

Ball Mount

3500 (1589 Kg.) 300 (136 Kg.)

Wiring Access Location: SUV1, SUV2

Form: F205 Rev A 5-6-05

Existing

weldnuts

Existing M10 Bolt

Existing M12 Bolt

Existing M10 Bolt

Existing M12 Bolt

Figure 1

Vehicle Forward

Driver’s Side

Frame Rail

Passenger’s

Side Frame

Rail

Remove

Bolts

Remove

Bolts

Figure 2

Note:Uses all existing

Bolts on Vehicle

Vehicle Frame

Fascia

Figure 1

Leave these bolts in

Drawbar Kit:

36061

Drawbar must be

used in the Rise

position only.

UHI 36332

Attention:

On some vehicles

air-conditioning lines

are very close to this

attachment. Be careful

not to damage lines when

installing hitch.

Chrysler Town & Country

Dodge Grand Caravan

VW Routan

A.C. line,

some models

Plastic loom,

magnified view

1 2 3

Inhaltsverzeichnis

Seite 1 - Installation Instructions

Installation InstructionsPart Numbers:901693645506550Hitch Shown In Proper PositionEquipment Required:Wrenches: 13mm, 15mm, 18mmDrill Bits: None1. Low

Seite 2 - Instructions d’installation

Instructions d’installationNuméros de pièces :901693645506550Attelage montré dans la position appropriéeÉquipement requis :Clés : 13 mm, 15 mm, 18 mmM

Seite 3 - Instrucciones de instalación

Instrucciones de instalaciónNúmeros de partes:901693645506550El enganche se muestra en la posición correcta Equipo necesario: Llaves: 13mm, 15mm, 18m