Draw-tite 36419 FRAME HITCH Bedienungsanleitung PDF herunterladen

Installation Instructions

Mazda CX-7

Part Numbers:

90154

36419

06401

Hitch Shown In Proper Position

Equipment Required: Metal file,

Pullwire (provided)

Wrenches: 11/16

Drill Bits: None

Fascia

1. Detach both (2) rear rubber muffler hangers to lower exhaust.

2. Enlarge either hole on bottom of both frame rails with a metal file enough to get spacer through.

3. Feed the pullwire through the newly enlarged hole, attach spacer and bolt and feed one at a time into the frame rail. Leave the

pullwire attached. Repeat on both frame rails as shown in Figure 2.

4. Feed the second spacer and bolt thru the enlarged hole and back out as shown in Figure 3. Leave the pullwire attached.

Repeat on both frame rails.

5. Feed the pullwires through the slot on the hitch brackets. Raise the hitch into position being careful not to push the fasteners

into the frame rails.

6. Attach remaining fasteners as shown Figure 1. Hand tighten only.

7. Check to assure hitch is centered on vehicle.

8. Tighten all fasteners to torque specifications.

9. Reattach rubber muffler hangers.

Rev. A6-23-0636419NSheet 1 of 3

z 2006 Cequent Towing Products

Nut 7/16-14Qty. (4)

SpacerQty. (4)

Conical WasherQty. (4)

Carriage Bolt 7/16-14 X 1.25Qty. (4)

Tighten all 7/16 GR5 fasteners with torque wrench to 50 Lb.-Ft. (68 N*M)

Note: check hitch frequently, making sure all fasteners and ball are properly tightened. If hitch is removed, plug all holes in trunk pan or other body panels to

prevent entry of water and exhaust fumes. A hitch or ball which has been damaged should be removed and replaced. Observe safety precautions when working

beneath a vehicle and wear eye protection. Do not cut access or attachment holes with a torch.

This product complies with safety specifications and requirements for connecting devices and towing systems of the state of New York, V.E.S.C. Regulation V-5

and SAE J684.

Fastener Kit: 36419F

Do Not Exceed Lower of Towing Vehicle

Manufacturer’s Rating or

Wiring Access Location: SUV3, SUV4

Figure 1.

Exhaust hanger

Frame rail

Existing holes

to be modified

Exhaust not

shown for clarity

Figure 3.

Figure 2.

Enlarged hole

Example of

pullwire procedure

Kink pullwire to

keep spacer

independent of bolt

Frame rail

Note:

Fasteners typical

both sides.

3500 LB, (1589 Kg) Max Gross Trailer Weight

300 LB, (136 Kg) Max Tongue Weight

Drawbar Kit:

36061

Drawbar must be used in the

Rise

position only.

Form: F205 Rev A 5-6-05

1 2 3

Inhaltsverzeichnis

Seite 1 - Installation Instructions

Installation InstructionsMazda CX-7Part Numbers:901543641906401Hitch Shown In Proper PositionEquipment Required: Metal file, Pullwire (provided)Wrench

Seite 2 - Instructions d’installation

Instructions d’installationMazda CX-7Numéros de pièces :Attelage montré dans la position appropriéeÉquipement requis : lime à métal, fil de tirage (fo

Seite 3 - Instrucciones de instalación

Instrucciones de instalaciónMazda CX-7Números de partes:El enganche se muestra en la posición correctaEquipo necesario: Lija de metal, cable de halar