Draw-tite 65064 FRONT MOUNT RECEIVER Bedienungsanleitung PDF herunterladen

Front Mounted Receiver

Installation Instructions

GM Sierra & Chevy Silverado 1500 Trucks-All

Part Numbers:

65064

1. It is necessary to either remove lower air dam or trim plastic air dam to install this hitch.

CONSULT VEHICLE OWNER BEFORE TRIMMING.

2. Using 1/2” bolt leaders pull 1/2” carriage bolts and blocks into access holes openings. Use reverse bolt leader method

for frame shoe installation. If needed ; lower or loosen splash shield to install the carriage bolt and block to cross

member. After fasteners are installed, reinstall the splash shield.

3. Note (Detail A) showing how to use 9/16” hardened flat washers and 1/2” Conical toothed washers to fill up space in

large 1-1/4” diameter holes in bottom of frame inside of frame shoes. Teeth on conical washers should be facing up.

4. Use tape, (Detail B) to hold washers in place before lifting hitch in to place.

5. Use 1/2” flat washers as needed between hitch and bottom of cross member to fill gap created by splash shield.

6. Install remaining fasteners as shown.

z 2013 Cequent Performance Products Sheet 1 of 3 65064N 8-7-13 Rev. A

Qty. (3) 1/2”-13 X 2-1/4” Carriage Bolt Qty. (3) 1/2” Flat Washer, * (As needed for gap)

Qty. (3) 1/4” X 1” X 3” Block; with square hole Qty. (3) 1/2” Hex Nut

Qty. (5) 1/2” Conical Toothed Washer Qty. (3) 1/2” Bolt Leader – Use eye protection, Safety First

Qty. (6) 9/16” Hardened Flat Washer

Tighten all 1/2” GR5 fasteners with torque wrench to 75 Lb.-Ft (102 N-M).

Note: check hitch frequently, making sure all fasteners and ball are properly tightened. If hitch is removed, plug all holes in trunk pan or other body

panels to prevent entry of water and exhaust fumes. A hitch or ball which has been damaged should be removed and replaced. Observe safety

precautions when working beneath a vehicle and wear eye protection. Do not cut access or attachment holes with a torch.

This product complies with safety specifications and requirements for connecting devices and towing systems of the state of New York, V.E.S.C.

Regulation V-5 and SAE J684.

Equipment Required:

Wrenches: 3/4”, 7/8”

Drill Bits: None

Fastener Kit: 65064F

CARGO CAPACITY – Do not exceed

500 LB. or Truck Front

Gross Axle Weight Rating, (GAWR).

9,000lb.

MAXIMUM WINCH LINE PULL

Receiver Shown In Proper Position

This is a magnified view

of a Bolt Leader

Air dam

Other: Tape, Marking chalk,

Tool to cut plastic air dam.

Other: Tape, Marking chalk,

Tool to cut plastic air dam.

Frame

shoe

Detail

Frame

shoe

Detail

Bumper

fascia

Cross member

Bolt Leader

Frame shoe

not shown

this side.

Access holes

Frame shoe

Printed in Mexico

Tape washers to

bottom of frame shoe

Splash shield

Truck frame

Reverse bolt leader Method

Frame shoe

9/16” Hardened flat washer

1/2” Conical toothed

washer with teeth

facing up

Note:

Fasteners

typical both

sides

1 2 3

Inhaltsverzeichnis

Seite 1 - Installation Instructions

Front Mounted ReceiverInstallation InstructionsGM Sierra & Chevy Silverado 1500 Trucks-AllPart Numbers:650641. It is necessary to either remove lo

Seite 2 - Instructions d’installation

Récepteur à montage avantInstructions d’installationCamions GM Sierra & Chevy Silverado 1500 –TousNuméro de pièce :650641. Remarque ! Pour install

Seite 3 - Instrucciones de instalación

Receptor instalado por el frenteInstrucciones de instalaciónCamionetas GM Sierra y Chevy Silverado 1500 -todosNúmeros de partes:650641. Es necesario r

Kommentare zu diesen Handbüchern

Keine Kommentare

Draw-tite 65064 FRONT MOUNT RECEIVER Bedienungsanleitung

Stöbern Sie online oder laden Sie Bedienungsanleitung nach Für das Auto Draw-tite 65064 FRONT MOUNT RECEIVER herunter. Draw-Tite 65064 FRONT MOUNT RECEIVER User Manual Benutzerhandbuch

Inhaltsverzeichnis

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Für das Auto Draw-tite 65064 FRONT MOUNT RECEIVER