5. Repeat step 3 for the passenger’s side using
the T-Connector containing the green wire.
6. Locate a suitable grounding point near the
connector. Clean dirt and rustproofing from
the area. Drill a 3/32" hole and secure the
white wire using the eyelet and screw
provided. (Do not drill into vehicle floor or
bed. Do not drill into any exposed surfaces.)
CAUTION
Verify what is behind any surface prior
to drilling to avoid damage to the vehicle
and/or personal injury. Do not drill into
any exposed surfaces.
WARNING
All connections must be complete for
the T-Connector to function properly.
For initial test, reset vehicle electrical
system by temporarily removing the key
from the ignition. Test and verify installation
with a test light or trailer once installed.
7. On the Driver’s side, mount the T-Connector
Black Box using the double-sided tape
provided. Secure the remainder of the
T-connector harness with the cable ties
provided, to prevent damage or rattling
and being careful to avoid any areas that
would cut or pinch the wire
e
.
8. Reinstall the taillight housing assemblies,
positioning the vehicle wiring harness
between the housing and the vehicle body.
9. Mount the 4-Flat end in an accessible
location with a bracket or electrical box
(not included).
WARNING
Overloading circuit can cause fires.
DO NOT exceed lower of towing
manufacturer rating or:
• Max. stop/turn light: 1 per side (2.1 amps)
• Max. tail lights: (5 amps)
Read vehicle's owners manual & instruction
sheet for additional information.
118431-037 Rev. B 02/26/09
ENGLISH
TOOLS REQUIRED:
Drill (3/32” Drill Bit), Philips Head Screwdriver
1. Open the rear lift gate. On the driver and
passenger sides of the vehicle, remove three
screws. Carefully pull the taillight away from
the vehicle being careful not to damage the
alignment pins
d
.
2. On the driver and passenger sides of the
vehicle, locate the vehicle's taillight wiring
harness. The taillight wiring harness will have
a connection point, on both sides, matching
the ends of the T-Connector. Separate this
connector, being careful not to break the
locking tabs. All connector surfaces should
be clean and free of dirt.
3. On the driver's side, insert the T-Connector
end, with the yellow wire, between the
vehicle wiring connectors and lock into place.
Ensure that the connectors are fully inserted
with locking tabs in place.
4. Route the harness containing the green
wire and the 4-Flat down the opening
behind the taillight on the driver’s side
e
.
Route harness containing the green wire
underneath the vehicle up through the
opening behind the passenger’s side taillight.
•
d
•
e
READ THIS FIRST:
Read and follow all vehicle warnings and
installation instructions before beginning
installation. Wear safety glasses and use
all safety precautions during installation.
LISEZ CECI EN PREMIER:
Lire et observer toutes les consignes de sécurité
et les instructions avant de commencer l’installa-
tion. Durant l’installation, veiller à toujours porter
des lunettes de protection et respecter les
mesures de sécurité.
LEA ESTO PRIMERO:
Lea y siga todas las advertencias e instrucciones
de instalación del vehículo antes de empezar la
instalación. Use gafas de seguridad y todas las
precauciones de seguridad durante la instalación.
Installation Instructions
Directives de Montage
Instrucciones de Instalación
T-Connector
Connecteur en T
Conector en T
Rondo
•
d
•
e
Soul
Kia Rondo
Kia Soul
(2 Seiten)
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Kommentare zu diesen Handbüchern