Draw-tite 118506 T-ONE CONNECTOR Bedienungsanleitung PDF herunterladen

ENGLISH

TOOLS REQUIRED:

Trim Panel Remover, 10mm Socket & Ratchet

or 10mm Wrench, Drill (3/32” Drill Bit),

1/4” socket, Wire Crimpers, Wire Cutters,

Philips Head Screwdriver, Test-probe

1. Open the rear tailgate to access the bolts that

hold the taillights in place

. Using a Phillips

head screwdriver, Remove the taillights on both

the driver and passenger side of the vehicle.

After removing the screws, carefully pull the

taillight away from the vehicle being careful

not to damage the alignment pins

2. On the Driver’s side, disconnect the vehicle wiring

harness from the taillight socket

. Separate this

connector, being careful not to break the locking

tabs. All connector surfaces should be clean and

free of dirt.

3. Using a Phillips head screwdriver, on the

Driver’s side, remove the plastic push pin that

is located closest to the tailgate weather strip.

Discard push pin

4. Gently pull the fascia back and route the module

under the interior fascia support. Rotate the

module to properly fit in-between fascia and body.

Line up bracket hole with the hole on the fascia

and support bracket from which the push pin

was removed

WARNING

Make sure module is mounted so that the epoxy

side of the module is pointed towards the ground

to prevent any water buildup.

Mount tow harness bracket under the interior fascia

support bracket with M6 Bolt (provided in kit).

On the driver’s side, insert the T-Connector end,

with the yellow wire, between the vehicle wiring

connectors and lock into place. Be careful not to

damage the locking tabs and be sure that connectors

are fully inserted with locking tabs in place.

7. Begining at the Driver’s side taillight pocket,

route the 4-Flat harness and harness containing

the green and red wires down, on the interior

side of the bumper brace

. Then route the

harness and 4-Flat across and underneath the

vehicle behind the bumper fascia. Route 4-Flat to

the center of the vehicle. Secure wire cable ties

provided. Continue to route the harness containing

the green wire up through the opening behind the

passenger’s side taillight.

WARNING

Route the wire being careful to avoid any hot

pipes, heat shields, the fuel tank or any other

points that may pinch or break the wire.

8. Repeat steps 2 & 3 on passenger’s side with

T-Connector end containing the green wire.

9. Locate a suitable grounding point on the driver’s

side near the connectors. Drill a 3/32” hole

and secure white wire with eyelet using screw

provided. Do not drill into any exposed surfaces.

CAUTION

Verify what is behind any surface prior to drilling

to avoid damage to the vehicle and/or personal

injury. Do not drill into any exposed surfaces.

10. On the driver’s side, locate the red 12 ga.

Power wire from the T-Connector box. Attach the

black 12 ga. wire provided. Route the remaining

wire through the opening in the taillight socket,

behind the bumper. Route the black wire along

the exterior frame or follow the existing wiring

along the thresholds into the engine compartment

up to the battery avoiding areas that may pinch

or break the wire

11.

Disconnect the vehicle’s Negative (-) battery cable.

If not removed, remove the fuse from the yellow

fuse holder (provided). After cutting the fuse holder

wire, attach the ring terminal and secure to the

vehicle’s Positive (+) battery cable

. Connect the

other end of the fuse holder to the black 12 ga.

wire, using the yellow butt connector (provided)

WARNING

Read and follow all warnings and cautions printed

on the tow vehicle’s battery.

12. Reconnect the vehicle’s Negative (-) battery cable

and install the 10 amp fuse into the fuse holder

from step 11.

WARNING

All connections must be complete for the

T-Connector to function properly. Test and verify

installation with a test light or trailer once installed.

For initial test, reset vehicle electrical system by

temporarily removing the key from the ignition.

13. Secure the remainder of the T-Connector harness

with the cable ties provided, to prevent damage or

rattling and being careful to avoid any areas that

would pinch, cut or melt the wire.

14. Reinstall taillight assemblies and other items

removed during installation, being careful not

to pinch or cut the wires.

WARNING

Overloading circuit can cause fires. DO NOT

exceed lower of towing manufacturer rating or:

• Max. stop/turn light: 2 per side (4.2 amps)

• Max. tail lights: (7.5 amps)

Read vehicle’s owners manual &

instruction sheet for additional information.

READ THIS FIRST:

Read and follow all vehicle warnings and installation

instructions before beginning installation. Wear safety

glasses and use all safety precautions during installation.

LISEZ CECI EN PREMIER:

Lire et observer toutes les consignes de sécurité et

les instructions avant de commencer l’installation.

Durant l’installation, veiller à toujours porter des lunettes

de protection et respecter les mesures de sécurité.

LEA ESTO PRIMERO:

Lea y siga todas las advertencias e instrucciones de

instalación del vehículo antes de empezar la instalación.

Use gafas de seguridad y todas las precauciones de

seguridad durante la instalación.

118506-037 Rev. C 1/5/2012

Installation Instructions

Directives de Montage

Instrucciones de Instalación

T-Connector

Connecteur en T

Conector en T

Kia Sorento

1 2

Inhaltsverzeichnis

Seite 1 - Kia Sorento

ENGLISHTOOLS REQUIRED: Trim Panel Remover, 10mm Socket & Ratchet or 10mm Wrench, Drill (3/32” Drill Bit), 1/4” socket, Wire Crimpers, Wire Cutte

Seite 2 - FraNçaIS

ESpaÑoLHERRAMIENTAS NECESSARIAS: TCorte el removedor de paneles, Encaje y trinquete de 10mm o llave de tuercas de 10mm, Taladro (broca de 3/32”), Lla

Kommentare zu diesen Handbüchern

Keine Kommentare

Draw-tite 118506 T-ONE CONNECTOR Bedienungsanleitung

Stöbern Sie online oder laden Sie Bedienungsanleitung nach Für das Auto Draw-tite 118506 T-ONE CONNECTOR herunter. Draw-Tite 118506 T-ONE CONNECTOR User Manual Benutzerhandbuch

Inhaltsverzeichnis

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Für das Auto Draw-tite 118506 T-ONE CONNECTOR