Draw-tite 75716 MAX-FRAME RECEIVER Bedienungsanleitung PDF herunterladen

Installation Instructions

Subaru Tribeca

Part Numbers:

75716

87611

44665

75243 U-Haul

Hitch Shown In Proper Position

Equipment Required: wire pulls (provided)

Wrenches: 11/16”, 7/8”

Drill Bits: None

Fastener Kit: 75716F

Do Not Exceed Lower of Towing Vehicle

Manufacturer’s Rating or

Hitch type

Max Gross

Trailer WT (LB)

Max Tongue

WT (LB)

Weight Distributing

5250 (2384 kg) 525 (238 kg)

Weight Carrying

Ball Mount

3500 (1589 kg) 525 (238 kg)

Wiring Access Location: SUV 8

FASTENERS ARE THE

SAME FROM SIDE TO SIDE

BUMPER

FRAME

1. Lower the spare tire from the underside of the vehicle.

2. Using the 7/16 wire pulls, insert the 7/16 Carriage bolts and 3/16 x 1” x 2” blocks through the end of the vehicle bumper structure

and through the existing holes. Keep wire pulls attached to bolts until hitch is in position.

3. Raise hitch into position and loosely install 7/16 Conical toothed washers and 7/16 Hex nuts as shown above.

4. Using the ½ wire pull insert the ½ Carriage bolts and ¼ X 1” X 3” Blocks through the side holes in the vehicle frame structure to

the existing holes in the vehicle frame rails and through the receiver.

5. Install ½ Conical toothed washers and ½ hex nuts.

6. Tighten all fasteners to the required torque specifications.

7. Raise spare tire back into position.

Tighten all 1/2-13 Gr5 fasteners with torque wrench to 75 Lb.-Ft. (102 N*M)

z 2011, 2012 Cequent Performance Products

Sheet 1 of 3 75716N 1-4-12 Rev. B

Qty. (2) Bolt carriage 7/16-14 x 1-1/2” Gr 5

Qty. (2) Bolt carriage 1/2-13 x 2 Gr 5

Qty. (2) Block – 1 x 2 x 3/16”

Qty. (2) Block – 1 x 3 x 1/4”

Qty. (2) Washer conical – 7/16”

Qty. (2) Washer conical – 1/2”

Qty. (2) Nut – 7/16”-14

Qty. (2) Nut – 1/2”-13

Tighten all 7/16-14 Gr5 fasteners with torque wrench to 50 Lb.-Ft. (68 N*M)

Note: check hitch frequently, making sure all fasteners and ball are properly tightened. If hitch is removed, plug all holes in trunk pan or other body panels to

prevent entry of water and exhaust fumes. A hitch or ball which has been damaged should be removed and replaced. Observe safety precautions when working

beneath a vehicle and wear eye protection. Do not cut access or attachment holes with a torch.

This product complies with safety specifications and requirements for connecting devices and towing systems of the state of New York, V.E.S.C. Regulation V-5

and SAE J684.

Form: F205 Rev A 5-6-05

1 2 3

Inhaltsverzeichnis

Seite 1 - 75243 U-Haul

Installation InstructionsSubaru TribecaPart Numbers:75716 87611 44665 75243 U-HaulHitch Shown In Proper PositionEquipment Requ

Seite 2

Instructions d’installationSubaru TribecaNuméros de pièces :Attelage montré dans la position appropriéeÉquipement requis : Fils de tirage (fourni)Clés

Seite 3

Instrucciones de instalaciónSubaru TribecaNúmeros de partes:El enganche se muestra en la posición correctaEquipo necesario: cables de halar (provistos

Kommentare zu diesen Handbüchern

Keine Kommentare

Draw-tite 75716 MAX-FRAME RECEIVER Bedienungsanleitung

Stöbern Sie online oder laden Sie Bedienungsanleitung nach Für das Auto Draw-tite 75716 MAX-FRAME RECEIVER herunter. Draw-Tite 75716 MAX-FRAME RECEIVER User Manual Benutzerhandbuch

Inhaltsverzeichnis

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Für das Auto Draw-tite 75716 MAX-FRAME RECEIVER