Draw-tite 75532 MAX-FRAME RECEIVER Bedienungsanleitung PDF herunterladen

Installation Instructions

Hyundai Veracruz

Part Numbers:

87439

75532

44573

Hitch Shown In Proper Position

Equipment Required:

Wrenches: 10mm, 14mm, 16mm

Drill Bits: None

Frame rail

NOTE: If present remove tow hook. Remove (2) bolts on the bottom of rail. To remove the remaining bolt lower exhaust

at the rubber isolator (2) places. Remove nuts holding the heat shield in place. Bolt is located on the inside of the

frame rail. Replace all nuts to heat shield except the one on the frame rail. Keep heat shield nut to be re-installed.

Return fasteners used for tow hook and the tow hook to owner.

1. Detach the rubber exhaust hangers and lower the rearward portion of the exhaust (2) on each exhaust).

2. Remove the (2) outboard nuts, one on each side, that holds the heat shield in place. Nuts to be re-installed

3. Rotate the hitch into position over the exhaust and align the slots to the existing weld nuts. NOTE: Make sure hitch

is between the heat shield and the frame rails. Install fasteners as shown.

4. Tighten bolts. Re-install heat shield nuts previously removed.

5. Raise exhaust system back into position.

Tighten all M10 CL10.9 fasteners with torquewrench to 58 Lb.-Ft. (79 N*M)

z2007, 2009 Cequent Performance Products

Sheet 1 of 3 75532N 9-2-09 Rev. B

j Qty. (4) Hex bolt M10X1.25X40mm CL10.9 k Qty. (4) Conical washer

Note: check hitch frequently, making sure all fasteners and ball are properly tightened. If hitch is removed, plug all holes in trunk pan or other body panels to

prevent entry of water and exhaust fumes. A hitch or ball which has been damaged should be removed and replaced. Observe safety precautions when working

beneath a vehicle and wear eye protection. Do not cut access or attachment holes with a torch.

This product complies with safety specifications and requirements for connecting devices and towing systems of the state of New York, V.E.S.C. Regulation V-5

and SAE J684.

Fastener Kit: 75532F

Do Not Exceed Lower of Towing Vehicle

Manufacturer’s Rating or

Hitch type

Max Gross

Trailer WT (LB)

Max Tongue

WT (LB)

Weight Distributing

5000 (2270 Kg) 500 (227 Kg)

Weight Carrying

Ball Mount

5000 (2270 Kg) 500 (227 Kg)

Wiring Access Location: SUV7

Form: F205 Rev A 5

Fascia

Frame rail

Remove Tow

hook if present.

Exhaust not

shown for clarity

Fasteners same

both sides

Weld nut

Bolt for Tow hook.

Existing weld nuts

Hitch pushes up slightly on bottom plastic

valance panel when installed. This is how the

hitch was designed to fit. Bottom valance

panel may be removed if customer chooses.

Valance panel

pushes up slightly

1 2 3

Inhaltsverzeichnis

Seite 1 - Installation Instructions

Installation InstructionsHyundai VeracruzPart Numbers:874397553244573Hitch Shown In Proper PositionEquipment Required:Wrenches: 10mm, 14mm, 16mmDrill

Seite 2 - Instructions d’installation

Instructions d’installationHyundai VeracruzNuméros de pièces :874397553244573Attelage montré dans la position appropriéeÉquipement requis :Clés : 10 m

Seite 3 - Instrucciones de instalación

Instrucciones de instalación Hyundai VeracruzNúmeros de partes:874397553244573El enganche se muestra en la posición correcta Equipo necesario:Llaves: