Draw-tite 59853 ROOF RACK Bedienungsanleitung PDF herunterladen

Direct Mount Track Rail System TR42

For use on sheet metal surfaces

For use with ROLA APE and APX cross bar kits

PART No.

Tools required to install

KIT COMPONENTS

59853

Part Description Qty

A Button head bolt M5 x 20mm 10

B Nylon washer 10

C Plus Nut Insert M5 10

D Hex bolt M5 x 30mm 1

E Hex Nut M6 1

F Washer M5 1

G Star Washer M5 10

H 3mm (.125”) Drill Bit 1

I .290 Dia. (“L”) Drill bit 1

J Hex Key- 3mm 1

K Silicone sealant 1

L Track and Isolator pad 2

M Track End Cap- closed (Front) 2

N Track End Cap- open (Rear) 2

Tools required:

A Masking tape F Tape measure

B Fine tip marker G Hammer

Center punch

Drill motor

Placement of Track Rails onto Vehicle surface (Crew Cab Truck shown)

Page 1 of 2

Align Tracks parallel to each other and equal distance

from rear.

Hint: pre-installing your ROLA cross bars on the tracks

will insure good placement.

Using a fine tip marker mark every other hole in track. Insure to mark the

holes on each end of the tracks.

DO NOT mark or drill every hole as it is not required.

Hint: Use masking tape to hold the tracks well in place while marking.

Isolator pad can be removed while marking.

Then use a center punch to set the drill position.

Use of ROLA track systems with Plus Nuts is intended for sheet

metal installations.

Install requires drilling and permanent installation of tracks.

Installation requires some tools and skill. If concerned please

have professionally installed.

Caution- never exceed the load rating for your

vehicle (contact manufacturer for details), or that

of your cross bar system which ever is lower.

Precaution Warnings before beginning

Printed in China

59853N Rev B 4-15-13

Center punch

Drill motor

D 8mm wrench I Safety glasses

E 10mm wrench

Mark every other hole in track

1 2 3 4 5 6

Inhaltsverzeichnis

Seite 1 - KIT COMPONENTS

Direct Mount Track Rail System TR42For use on sheet metal surfacesFor use with ROLA APE and APX cross bar kitsPART No.Tools required to installKIT COM

Seite 2

Remove rails after markingHint- it’s not advisable to drill through the rails.Drill 3mm pilot hole first, then drill .290” dia. holes. Blow or vacuu

Seite 3 - COMPOSANTS DE L'ENSEMBLE

Système de rails pour montage direct TR42Pour utilisation sur surface de tôlePour utilisation avec les ensembles de traverses ROLA APE et APXNoPIÈCEOu

Seite 4

Enlever les rails après le marquage.Conseil : Il n'est pas recommandé de percer à travers les rails.Percer d'abord un trou de guidage 3mm, p

Seite 5 - COMPONENTES DEL KIT

Sistema de rieles para montaje directo TR42Para uso sobre superficies de metal laminadoUse con kits de travesaños APE y APX de ROLAPARTE No.Herramient

Seite 6

Quite los rieles después de marcarSugerencia: No es recomendable perforar a través de los rieles.Taladre un orificio piloto de 3mm primero, luego tala

Kommentare zu diesen Handbüchern

Keine Kommentare

Draw-tite 59853 ROOF RACK Bedienungsanleitung

Stöbern Sie online oder laden Sie Bedienungsanleitung nach Für das Auto Draw-tite 59853 ROOF RACK herunter. Draw-Tite 59853 ROOF RACK User Manual Benutzerhandbuch

Inhaltsverzeichnis

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Für das Auto Draw-tite 59853 ROOF RACK