3. Route the OE wire connectors through the 2"
hole being careful not to scrape or damage
the wires against the sharp edges of the
sheet metal
gh
. Using the 7-way end as a
guide, mark the mounting hole locations with
a center punch
i
. Slide the 7-Way end back
and then drill four 3/32" holes as marked.
CAUTION
Verify what is behind any surface prior
to drilling to avoid damage to the vehicle
and/or personal injury. Do not drill into any
exposed surfaces.
NOTE
Use rust-proof coating in drilled areas
to prevent future rusting (not provided).
4. Using the 4 self- tapping screws, mount
the 7-way harness to the vehicle surface.
NOTE
Use spacer provided in-between the 7-Way
plug and the truck bed if the 90 degree bend
corner is too close to the outside wall of the
truck bed
j
.
WARNING
Route the wire being careful to avoid any hot
pipes, heat shields, the fuel tank or any other
points that may pinch or break the wire.
5. Locate the vehicle’s 7-way factory harness
on or near the rear bumper. Separate this
connector, being careful not to break the
locking tabs. All connector surfaces should
be clean and free of dirt. Install the Trailer
Tow Harness between the mating plugs
k
.
NOTE
Dodge version is rectangular.
WARNING
All connections must be complete for the
Trailer Tow Harness to function properly.
Test and verify installation with a test light
or trailer once installed.
NOTE
On some vehicles you may need to add a
fuse or relay (not provided) to complete all
of the functions going to the 7-way. Consult
your owner’s manual for locations.
6. Secure all loose wiring.
5197410-037 Rev. A 05/18/07
ENGLISH
TOOLS REQUIRED:
Drill (3/32” & 1/4" Drill Bits), 2" Hole Saw,
5/16" Socket, Center Punch
1. Determine a suitable mounting point on the
tow vehicle for the adapter, usually on the
Driver's side between the rear cab post and
in front of the wheel well area
d
.
NOTE
Cut away view of truck rail. Make sure there
is clearance for mounting
e
.
2. Once a suitable mounting location is found,
drill a pilot hole using a drill and 1/4” bit
f
.
Re-check your mounting location and wire
lengths and then use your 2” hole saw to
finish cutting the mounting hole.
CAUTION
Verify what is behind any surface prior
to drilling to avoid damage to the vehicle
and/or personal injury. Do not drill into
any exposed surfaces.
NOTE
If the vehicle has a bedliner it will need to
be notched or use a longer set of screws
(not provided) and mount directly into the
bedliner and body panel.
NOTE
Use rust-proof coating in drilled areas
to prevent future rusting (not provided).
•
d
•
g
•
f
•
h
•
i
READ THIS FIRST:
Read and follow all vehicle warnings and installation
instructions before beginning installation. Wear safety
glasses and use all safety precautions during installation.
LISEZ CECI EN PREMIER:
Lire et observer toutes les consignes de sécurité et les
instructions avant de commencer l’installation. Durant
l’installation, veiller à toujours porter des lunettes de
protection et respecter les mesures de sécurité.
LEA ESTO PRIMERO:
Lea y siga todas las advertencias e instrucciones de
instalación del vehículo antes de empezar la instalación.
Use gafas de seguridad y todas las precauciones de
seguridad durante la instalación.
Installation Instructions
Directives de Montage
Instrucciones de Instalación
Trailer Tow Harness
Faisceau de Fils D'attelage
de Remorque
Arnés de Remolque
•
j
•
k
•
e
(2 Seiten)
(2 Seiten)
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Kommentare zu diesen Handbüchern