Draw-tite 24890 SPORTFRAME HITCH Bedienungsanleitung PDF herunterladen

Installation Instructions

Dodge Dart

Part Numbers:

Hitch Shown In Proper Position

Wiring Access Location: P3, 4

Equipment Required:

Wrenches: 3/4”

Drill Bits: None

Access hole

Do Not Exceed Lower of Towing Vehicle

Manufacturer’s Rating or

Drawbar must be used in the

RISE position only.

Drawbar Kit:

3592

Fastener Kit: 24890F

24890

60309

77278

2000 LB (908 Kg) Max Gross Trailer Weight

200 LB (90.8 Kg) Max Tongue Weight

Note: Fasteners typical

both sides

Exhaust, heat shield

and trunk not shown.

Frame rail

Fascia

Frame rail

Figure 2.

Note: on dual exhaust with appearance panels is a tight working area. Wait until exhaust pipes have cooled to install hitch.

1. Remove (2) round plugs side of frame rail and (1) square plug from bottom of the frame rail, each side. Return (4) round plugs to owner.

2. Feed the pull wire through the holes in the side of the frame and out through the access holes, attach spacer and bolt and feed one at a

time into the frame rail. Leave the pull wire attached. Repeat on both frame rails.

3. Push carriage bolt with pull wire attached back into the frame rail leaving pull wire sticking out. As shown in Figure 2.

4. Feed pull wires through the holes on the brackets.

5. Raise hitch into position as shown. Figure 1 Note: on dual exhaust locate the hitch near the muffler then raise along exhaust pipes and

move rearward into position

6. Pull carriage bolts back into place, carefully remove pull wire and attach conical washers and hex nuts.

7. Torque all fasteners to specifications.

8. Reinstall square plugs removed in step 1.

Sheet 1 of 3 24890N 7-25-12 Rev. A

Qty. (4) Carriage bolt ½-13 X 2.00 Gr5

Qty. (4) Hex nut ½-13

Qty. (4) Spacer ¼” X 1.00 X 3.00

Qty. (4) Pull wire ½”

Qty. (4) Conical washer ½”

Note: check hitch frequently, making sure all fasteners and ball are properly tightened. If hitch is removed, plug all holes in trunk pan or other body panels to

prevent entry of water and exhaust fumes. A hitch or ball which has been damaged should be removed and replaced. Observe safety precautions when working

beneath a vehicle and wear eye protection. Do not cut access or attachment holes with a torch.

This product complies with safety specifications and requirements for connecting devices and towing systems of the state of New York, V.E.S.C. Regulation V-5

and SAE J684.

Form F206 Rev A 5605

Tighten all ½-13 GR5 fasteners with torque wrench to 75 Lb.-Ft. (102 N*M)

Kink pull wire to keep block

independent of bolt

Figure 1.

1 2 3

Inhaltsverzeichnis

Seite 1 - Installation Instructions

Installation InstructionsDodge DartPart Numbers:Hitch Shown In Proper PositionWiring Access Location: P3, 4Equipment Required:Wrenches: 3/4”Drill Bits

Seite 2 - Instructions d’installation

Instructions d’installationDodge DartNuméros de pièce :Attelage montré dans la position appropriéePoints d'accès au câblage : P3, 4Équipement req

Seite 3 - Instrucciones de instalación

Instrucciones de instalaciónDodge DartNúmeros de partes:El enganche se muestra en la posición correctaUbicación del acceso al cableado: P3, 4Equipo ne

Kommentare zu diesen Handbüchern

Keine Kommentare

Draw-tite 24890 SPORTFRAME HITCH Bedienungsanleitung

Stöbern Sie online oder laden Sie Bedienungsanleitung nach Für das Auto Draw-tite 24890 SPORTFRAME HITCH herunter. Draw-Tite 24890 SPORTFRAME HITCH User Manual Benutzerhandbuch

Inhaltsverzeichnis

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Für das Auto Draw-tite 24890 SPORTFRAME HITCH