Draw-tite 118593 T-ONE CONNECTOR Bedienungsanleitung PDF herunterladen

ENGLISH

TOOLS NEEDED:

Trim Panel Remover, 10mm Socket &

Ratchet or 10mm Wrench, Drill (3/32” Drill

Bit), 1/4” socket, Wire Crimpers, Wire Cutters,

Philips Head Screwdriver, Test-probe

1. Open the vehicle’s rear tailgate

.Remove

threshold, trunk floor panels and trays. Set

aside all items removed being careful not to

damage parts.

2. On both sides of the vehicle, remove cargo

loops and phillips head screws

, so that

the trim panels can be carefully pulled away

from the vehicle.

3. On the driver and passenger sides of the

vehicle, locate the vehicle’s taillight wiring

harness

. Separate this connector, being

careful not to break the locking tabs. Check

to see that the mating surfaces of the vehicle

wiring connectors match the T-Connector

ends. All connector surfaces should be

clean and free of dirt.

4. On the driver’s side, attach the end of the

T-Connector containing the yellow and the

brown wires. Ensure that the connectors

are fully inserted with locking tabs in place.

5. Route the T-Connector containing the

green wire below the threshold cover to the

passenger’s side taillight housing. Repeat step

4 using the T-Connector ends containing the

green wire.

NOTE

Route the 4-Flat from below the driver’s side

trim panel into rear storage compartment.

Store there when not in use.

6. On driver’s side, locate a flat surface in a out

of the way place and mount the T-Connector’s

black convertor box with the double sided tape.

7. Locate a suitable grounding point near the

connector such as the vehicle’s frame or cross

member. (Do not drill into vehicle floor or bed.)

Clean dirt and rustproofing from area. Drill a

3/32” hole and secure white wire using eyelet

and screw provided.

CAUTION

Verify what is behind any surface prior to

drilling to avoid damage to the vehicle and/

or personal injury. Do not drill into any

exposed surfaces.

8. On the driver’s side, locate the black 12 ga.

power wire from the T-Connector box.

Attach the black 12 ga. wire provided.

9. Either route the black wire thru a grommet

and along the exterior frame or follow the

existing wiring along the thresholds into the

engine compartment up to the battery avoiding

areas that may pinch or break the wire

WARNING

If routing the wire thru a grommet and along

the exterior of the vehicle, be careful to avoid

any hot pipes, heat shields, the fuel tank or any

other points that may pinch or break the wire.

10. Disconnect the vehicle’s Negative (-) battery

cable. If not removed, remove the fuse from the

yellow fuse holder (provided). After cutting the

fuse holder wire

, attach the ring terminal and

secure to the vehicle’s Positive (+) battery cable

.Connect the other end of the fuse holder

to the black 12 ga. wire, using the yellow butt

connector (provided)

WARNING

Read and follow all warnings and cautions

printed on the tow vehicle’s battery.

11. Reconnect the vehicle’s Negative (-) battery

cable and install the 10 amp fuse into the

fuse holder from Step 10.

WARNING

All connections must be complete for the

T-Connector to function properly. Test and

verify installation with a test light or trailer

once installed. For initial test, reset vehicle

electrical system by temporarily removing

the key from the ignition.

12. Secure the remainder of the T-Connector

harness with the cable ties provided, to prevent

damage or rattling and being careful to avoid

any areas that would pinch, cut or melt the wire.

13. Reinstall the plastic trim panels, threshold,

storage covers, floor covering and other items

removed during installation, being careful not

to pinch or cut the wires.

WARNING

Overloading circuit can cause fires. DO NOT

exceed lower of towing manufacturer rating or:

• Max. stop/turn light: 1 per side (4.2 amps)

• Max. tail lights: (7.5 amps)

Read vehicle’s owners manual & instruction

sheet for additional information.

READ THIS FIRST:

Read and follow all vehicle warnings and installation

instructions before beginning installation. Wear safety

glasses and use all safety precautions during installation.

LISEZ CECI EN PREMIER:

Lire et observer toutes les consignes de sécurité et

les instructions avant de commencer l’installation.

Durant l’installation, veiller à toujours porter des lunettes

de protection et respecter les mesures de sécurité.

LEA ESTO PRIMERO:

Lea y siga todas las advertencias e instrucciones de

instalación del vehículo antes de empezar la instalación.

Use gafas de seguridad y todas las precauciones de

seguridad durante la instalación.

118593-037 Rev. B 6/27/2013

Installation Instructions

Directives de Montage

Instrucciones de Instalación

T-Connector

Connecteur en T

Conector en T

Inﬁniti FX35, FX37 and FX50

d g

ife

1 2

FraNçaIS 2

Inhaltsverzeichnis

Seite 1

ENGLISHTOOLS NEEDED: Trim Panel Remover, 10mm Socket & Ratchet or 10mm Wrench, Drill (3/32” Drill Bit), 1/4” socket, Wire Crimpers, Wire Cutters,

Seite 2 - FraNçaIS

ESpaÑoLHERRAMIENTAS NECESSARIAS: Corte el removedor de paneles, Encaje y trinquete de 10mm o llave de tuercas de 10mm, Taladro (broca de 3/32”), Lla

Kommentare zu diesen Handbüchern

Keine Kommentare

Draw-tite 118593 T-ONE CONNECTOR Bedienungsanleitung

Stöbern Sie online oder laden Sie Bedienungsanleitung nach Für das Auto Draw-tite 118593 T-ONE CONNECTOR herunter. Draw-Tite 118593 T-ONE CONNECTOR User Manual Benutzerhandbuch

Inhaltsverzeichnis

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Für das Auto Draw-tite 118593 T-ONE CONNECTOR