Draw-tite 118444 T-ONE CONNECTOR Bedienungsanleitung PDF herunterladen

118444-037 Rev. A 09/13/07

ENGLISH

TOOLS NEEDED:

Wire Cutters, Trim Panel Remover, Drill (3/32” Drill Bit),

Philips Head Screwdriver, Test-probe, Wire Crimpers

1. Open the trunk to remove the vehicle’s taillight

assemblies. Start by locating and removing the plastic

wing nuts (2 per side). They are located on both sides in

the trunk behind the taillights, set aside

. Carefully pry

the housings away from the vehicle, being careful not to

break the alignment tabs.

2. On the driver and passenger sides of the vehicle, locate

the vehicle’s taillight wiring harness. The taillight wiring

harness will have a connection point, on both sides,

matching the ends of the T-Connector

. Separate this

connector, being careful not to break the locking tabs.

All connector surfaces should be clean and free of dirt.

3. On the driver’s side, insert the T-Connector end, with

the yellow wire, between the vehicle wiring connectors

and lock into place. On the driver’s side, insert the

T-Connector end, with the brown and red wire, between

the vehicle wiring connectors and lock into place. Be

careful not to damage the locking tabs and be sure that

connectors are fully inserted with locking tabs in place.

4. Route the harness containing the green wire and

the 4-Flat down the opening behind the taillight

on the driver’s side

. Route the 4-Flat harness

underneath and to the center of the vehicle. Route

harness containing the green wire underneath the

vehicle up through the opening behind the passenger’s

side taillight.

WARNING

Route the wire being careful to avoid any hot pipes, heat

shields, the fuel tank or any other points that may pinch

or break the wire.

5. Repeat step 3 for the passenger’s side using the

T-Connector containing the green wire.

6. Locate a suitable grounding point near the connector.

Clean dirt and rustproofing from the area. Drill a 3/32”

hole and secure the white wire using the eyelet and

screw provided. (Do not drill into vehicle floor or bed.

Do not drill into any exposed surfaces.)

CAUTION

Verify what is behind any surface prior to drilling to

avoid damage to the vehicle and/or personal injury. Do

not drill into any exposed surfaces.

7. Disconnect the vehicle’s Negative (-) battery cable

If not removed, remove the fuse from the yellow fuse

holder (provided). After cutting the fuse holder wire

attach the ring terminal and secure to the vehicle’s

Positive (+) battery cable

. Connect the other end

of the fuse holder to the black 12 ga. wire, using the

yellow butt connector (provided).

CAUTION

Read and follow all warnings and cautions printed on

the tow vehicle's battery.

8. Route the black wire out of the engine compartment and

to the rear driver’s side of the vehicle

. Connect the

other end of the black 12 ga. wire to the red power wire

located on the T-Connector’s black box, using the yellow

butt connector (provided).

WARNING

Route the wire being careful to avoid any hot pipes, heat

shields, the fuel tank or any other points that may pinch

or break the wire.

9. Reconnect the vehicle’s Negative (-) battery cable

and install the 10 amp fuse into the fuse holder from

step 7

WARNING

All connections must be complete for the T-Connector to

function properly. Test and verify installation with a test

light or trailer once installed. For initial test, reset vehicle

electrical system by temporarily removing the key from

the ignition.

10. On the driver’s side, mount the T-Connector black

box using the double-sided tape provided. Secure

the remainder of the T-connector harness with the

cable ties provided, to prevent damage or rattling

and being careful to avoid any areas that would cut

or pinch the wire.

11. Reinstall the taillight housing assemblies, positioning

the vehicle wiring harness between the housing and

the vehicle body.

12. Mount the 4-Flat end in an accessible location with

a bracket or electrical box (not included).

WARNING

Overloading circuit can cause fires. DO NOT exceed

lower of towing manufacturer rating or:

• Max. stop/turn light: 1 per side (2.1 amps)

• Max. tail lights: (4.2 amps)

Read vehicle’s owners manual & instruction sheet for

additional information.

•

Installation Instructions

Directives de Montage

Instrucciones de Instalación

T-Connector

Connecteur en T

Conector en T

READ THIS FIRST:

Read and follow all vehicle warnings and installation instructions

before beginning installation. Wear safety glasses and use all

safety precautions during installation.

LISEZ CECI EN PREMIER:

Lire et observer toutes les consignes de sécurité et les instruc-

tions avant de commencer l’installation. Durant l’installation,

veiller à toujours porter des lunettes de protection et respecter

les mesures de sécurité.

LEA ESTO PRIMERO:

Lea y siga todas las advertencias e instrucciones de instalación

del vehículo antes de empezar la instalación. Use gafas de

seguridad y todas las precauciones de seguridad durante

la instalación.

•

(+)

(-)

Chrysler Sebring

1 2

FRANÇAIS 2

Inhaltsverzeichnis

Seite 1

118444-037 Rev. A 09/13/07ENGLISHTOOLS NEEDED:Wire Cutters, Trim Panel Remover, Drill (3/32” Drill Bit),Philips Head Screwdriver, Test-probe, Wire Cri

Seite 2 - FRANÇAIS

FRANÇAISOUTILS REQUIS: Coupe-fils, Écarteur de panneau de garnisage, Perceuse(mèche de 3/32 po), Tournevis à pointe cruciforme,Sonde de vérification,

Kommentare zu diesen Handbüchern

Keine Kommentare

Draw-tite 118444 T-ONE CONNECTOR Bedienungsanleitung

Stöbern Sie online oder laden Sie Bedienungsanleitung nach Für das Auto Draw-tite 118444 T-ONE CONNECTOR herunter. Draw-Tite 118444 T-ONE CONNECTOR User Manual Benutzerhandbuch

Inhaltsverzeichnis

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Für das Auto Draw-tite 118444 T-ONE CONNECTOR